Post Stock Login Register

EN 10088-3 X2CrNiMnMoCuN24-4-3-2 vs ASTM A959 S32950

Close Alternative — 71% match based on chemical composition and mechanical property overlap.

EN 10088-3 X2CrNiMnMoCuN24-4-3-2 (EN 10088-3:2014) and ASTM A959 S32950 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X2CrNiMnMoCuN24-4-3-2 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while ASTM A959 S32950 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). EN 10088-3 X2CrNiMnMoCuN24-4-3-2 is defined under European Standard (EN), originating from Europe, while ASTM A959 S32950 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-3 X2CrNiMnMoCuN24-4-3-2 vs ASTM A959 S32950 is a 71% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 71%.

Frequently Compared With EN 10088-3 X2CrNiMnMoCuN24-4-3-2:
ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
71%
MECHANICAL MATCH
No shared data
OVERALL
71%
Specifications
Property EN 10088-3 X2CrNiMnMoCuN24-4-3-2 ASTM A959 S32950
Standard EN 10088-3:2014 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=0.70 <=0.60
Mn (%) 2.50-4.0 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.005 <=0.010
Cr (%) 23.0-25.0 26.0-29.0
Mo (%) 1.00-2.00 1.00-2.50
Ni (%) 3.0-4.5 3.5-5.2
N (%) 0.20-0.30 0.15-0.35
Cu (%) 0.10-0.80 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X2CrNiMnMoCuN24-4-3-2 ASTM A959 S32950
Tensile Strength 650-900 MPa Not specified
Yield Strength >=450 MPa Not specified
Elongation >=25% Not specified
Hardness <=290 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Typical Applications
EN 10088-3 X2CrNiMnMoCuN24-4-3-2
General purposes, semi-finished products, bars, rods, wire, sections and bright products
ASTM A959 S32950
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can EN 10088-3 X2CrNiMnMoCuN24-4-3-2 Be Substituted With ASTM A959 S32950?
EN 10088-3 X2CrNiMnMoCuN24-4-3-2 and ASTM A959 S32950 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-3 X2CrNiMnMoCuN24-4-3-2
0 active listings and RFQs →
ASTM A959 S32950
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X2CrNiMnMoCuN24-4-3-2 and ASTM A959 S32950?
EN 10088-3 X2CrNiMnMoCuN24-4-3-2 specifies Cu which is not specified for ASTM A959 S32950.
Can EN 10088-3 X2CrNiMnMoCuN24-4-3-2 be substituted with ASTM A959 S32950?
EN 10088-3 X2CrNiMnMoCuN24-4-3-2 and ASTM A959 S32950 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.