Close Alternative — 83% match
based on chemical composition and mechanical property overlap.
EN 10088-3 X2CrTi17 (EN 10088-3:2014) and EN 10088-3 X3CrNb17 (EN 10088-3:2014) are both steel grades.
Both fall under the Stainless Steel category.
EN 10088-3 X2CrTi17 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while EN 10088-3 X3CrNb17 is commonly used for general purposes, semi-finished products, bars, rods, wire, sections and bright products.
EN 10088-3 X2CrTi17 is defined under European Standard (EN), originating from Europe, while EN 10088-3 X3CrNb17 is defined under European Standard (EN), originating from Europe.
As per chemical composition, EN 10088-3 X2CrTi17 vs EN 10088-3 X3CrNb17 is a 74.5% match.
As per mechanical properties, the match is 100%.
Combined, this makes them a close alternative overall at 83%.
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
EN 10088-3 X2CrTi17
EN 10088-3 X3CrNb17
Tensile Strength
420-620 MPa
420-620 MPa
Yield Strength
>=200 MPa
>=200 MPa
Elongation
>=20%
>=20%
Hardness
<=200 HB
<=200 HB
Condition
Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 50 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only
Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 50 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only
Typical Applications
EN 10088-3 X2CrTi17
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-3 X3CrNb17
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Key Differences
EN 10088-3 X2CrTi17 specifies N, Ti which are not specified for EN 10088-3 X3CrNb17.
EN 10088-3 X3CrNb17 specifies Nb which is not specified for EN 10088-3 X2CrTi17.
Can EN 10088-3 X2CrTi17 Be Substituted With EN 10088-3 X3CrNb17?
EN 10088-3 X2CrTi17 and EN 10088-3 X3CrNb17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
What is the difference between EN 10088-3 X2CrTi17 and EN 10088-3 X3CrNb17?
EN 10088-3 X2CrTi17 specifies N, Ti which are not specified for EN 10088-3 X3CrNb17. EN 10088-3 X3CrNb17 specifies Nb which is not specified for EN 10088-3 X2CrTi17.
Can EN 10088-3 X2CrTi17 be substituted with EN 10088-3 X3CrNb17?
EN 10088-3 X2CrTi17 and EN 10088-3 X3CrNb17 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.