Post Stock Login Register

EN 10088-3 X70CrMo15 vs EN 10088-1 X50CrMoV15

Close Alternative — 78.9% match based on chemical composition and mechanical property overlap.

EN 10088-3 X70CrMo15 (EN 10088-3:2014) and EN 10088-1 X50CrMoV15 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X70CrMo15 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X50CrMoV15 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X70CrMo15 vs EN 10088-1 X50CrMoV15 is a 78.9% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 78.9%.

Frequently Compared With EN 10088-3 X70CrMo15:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
78.9%
MECHANICAL MATCH
No shared data
OVERALL
78.9%
Specifications
Property EN 10088-3 X70CrMo15 EN 10088-1 X50CrMoV15
Standard EN 10088-3:2014 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) 0.60-0.75 0.35-0.55
Si (%) <=0.70 <=1.00
Mn (%) <=1.00 <=1.00
P (%) <=0.040 <=0.040
S (%) <=0.030 <=0.015
Cr (%) 14.0-16.0 14.0-15.5
Mo (%) 0.40-0.80 0.50-0.80
V (%) Not specified 0.10-0.20
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X70CrMo15 EN 10088-1 X50CrMoV15
Tensile Strength <=900 MPa Not specified
Hardness <=280 HB Not specified
Condition Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 100 mm; hardness for guidance only Not specified
Typical Applications
EN 10088-3 X70CrMo15
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 X50CrMoV15
Not documented
Key Differences
Can EN 10088-3 X70CrMo15 Be Substituted With EN 10088-1 X50CrMoV15?
EN 10088-3 X70CrMo15 and EN 10088-1 X50CrMoV15 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-3 X70CrMo15
0 active listings and RFQs →
EN 10088-1 X50CrMoV15
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X70CrMo15 and EN 10088-1 X50CrMoV15?
EN 10088-1 X50CrMoV15 specifies V which is not specified for EN 10088-3 X70CrMo15.
Can EN 10088-3 X70CrMo15 be substituted with EN 10088-1 X50CrMoV15?
EN 10088-3 X70CrMo15 and EN 10088-1 X50CrMoV15 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.