Post Stock Login Register

EN ISO 4957 X155CrVMo12-1 vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN ISO 4957 X155CrVMo12-1 (EN ISO 4957:2018) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. EN ISO 4957 X155CrVMo12-1 is typically used for blanking dies, forming dies, thread rolling dies, gauges, while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. EN ISO 4957 X155CrVMo12-1 is defined under European Standard (EN), originating from Europe, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN ISO 4957 X155CrVMo12-1 vs EN ISO 4957 1.2316 is a 56.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN ISO 4957 X155CrVMo12-1:
EN ISO 683-17 100Cr6 DIN EN ISO 4957 1.2344 GOST 5950 3H2W8F GOST 5950 4H5MFS GOST 5950 4H5MFS1 DIN EN ISO 4957 1.2379 GB/T 1299 3Cr2W8V GB/T 1299 4Cr5MoSiV GB/T 1299 4Cr5MoSiV1 AISI 52100 IS 1570 (Part 6) 103T3
Other Tool & Die Steels Grades to Compare With EN ISO 4957 X155CrVMo12-1:
IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
56.8%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property EN ISO 4957 X155CrVMo12-1 EN ISO 4957 1.2316
Standard EN ISO 4957:2018 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 1.55–1.65 ≤0.06
Mn (%) 0.20–0.50 ≤1.00
Cr (%) 11.50–12.50 15.5–17.5
Mo (%) 0.60–0.80 0.80–1.30
V (%) 0.70–1.00 Not specified
Si (%) ≤0.40 ≤0.50
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN ISO 4957 X155CrVMo12-1 EN ISO 4957 1.2316
Hardness HRC (hardened) 58–62 38–44
Hardness HB (annealed) ≤255 Not specified
Wear Resistance Excellent Not specified
Hardness HRC Not specified 28–34 (pre-hardened)
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
EN ISO 4957 X155CrVMo12-1
Blanking dies, forming dies, thread rolling dies, gauges
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can EN ISO 4957 X155CrVMo12-1 Be Substituted With EN ISO 4957 1.2316?
EN ISO 4957 X155CrVMo12-1 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN ISO 4957 X155CrVMo12-1
Round Bar → (3 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2500–3200 mm (98.43–125.98 in)
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
EN ISO 4957 X155CrVMo12-1
3 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN ISO 4957 X155CrVMo12-1 and EN ISO 4957 1.2316?
EN ISO 4957 X155CrVMo12-1 specifies V which is not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Ni which is not specified for EN ISO 4957 X155CrVMo12-1.
Can EN ISO 4957 X155CrVMo12-1 be substituted with EN ISO 4957 1.2316?
EN ISO 4957 X155CrVMo12-1 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.