Post Stock Login Register

EN ISO 4957 X30WCrV9-3 vs EN ISO 4957 1.2316

Minimal Match — 28.8% match based on chemical composition and mechanical property overlap.

EN ISO 4957 X30WCrV9-3 (EN ISO 4957:2018) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. EN ISO 4957 X30WCrV9-3 is typically used for hot extrusion dies, hot forging dies for non-ferrous metals, while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. EN ISO 4957 X30WCrV9-3 is defined under European Standard (EN), originating from Europe, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN ISO 4957 X30WCrV9-3 vs EN ISO 4957 1.2316 is a 43.2% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 28.8%.

Frequently Compared With EN ISO 4957 X30WCrV9-3:
AISI 52100 DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS1 DIN EN ISO 4957 1.2379 GOST 5950 3H2W8F GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS GB/T 1299 3Cr2W8V IS 1570 (Part 6) 103T3
Other Tool & Die Steels Grades to Compare With EN ISO 4957 X30WCrV9-3:
IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
43.2%
MECHANICAL MATCH
0%
OVERALL
28.8%
Specifications
Property EN ISO 4957 X30WCrV9-3 EN ISO 4957 1.2316
Standard EN ISO 4957:2018 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 0.26–0.36 ≤0.06
Si (%) 0.15–0.50 ≤0.50
Mn (%) 0.15–0.40 ≤1.00
Cr (%) 2.50–3.50 15.5–17.5
W (%) 8.50–10.00 Not specified
V (%) 0.30–0.60 Not specified
Mo (%) Not specified 0.80–1.30
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN ISO 4957 X30WCrV9-3 EN ISO 4957 1.2316
Hardness HRC (hardened) 38–52 38–44
Hardness HB (annealed) ≤229 Not specified
Hardness HRC Not specified 28–34 (pre-hardened)
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
EN ISO 4957 X30WCrV9-3
Hot extrusion dies, hot forging dies for non-ferrous metals
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can EN ISO 4957 X30WCrV9-3 Be Substituted With EN ISO 4957 1.2316?
EN ISO 4957 X30WCrV9-3 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN ISO 4957 X30WCrV9-3
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2800–3600 mm (110.24–141.73 in)
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
EN ISO 4957 X30WCrV9-3
2 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN ISO 4957 X30WCrV9-3 and EN ISO 4957 1.2316?
EN ISO 4957 X30WCrV9-3 specifies W, V which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Mo, Ni which are not specified for EN ISO 4957 X30WCrV9-3.
Can EN ISO 4957 X30WCrV9-3 be substituted with EN ISO 4957 1.2316?
EN ISO 4957 X30WCrV9-3 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.