Post Stock Login Register

GB/T 1299 Cr12MoV vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

GB/T 1299 Cr12MoV (GB/T 1299-2014) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. GB/T 1299 Cr12MoV is typically used for blanking dies, forming dies, thread rolling dies, punches, shear blades, gauges, broaches, drawing dies, while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. GB/T 1299 Cr12MoV is defined under Guobiao Standards (GB/T), originating from China, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, GB/T 1299 Cr12MoV vs EN ISO 4957 1.2316 is a 62.2% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With GB/T 1299 Cr12MoV:
DIN EN ISO 4957 1.2379 DIN EN ISO 4957 1.2344 GB/T 1299 4Cr5MoSiV1 AISI 52100 EN ISO 683-17 100Cr6 GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS1 GOST 5950 4H5MFS GB/T 1299 3Cr2W8V GOST 5950 3H2W8F IS 1570 (Part 6) 103T3 IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
62.2%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property GB/T 1299 Cr12MoV EN ISO 4957 1.2316
Standard GB/T 1299-2014 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 1.45–1.70 ≤0.06
Mn (%) ≤0.40 ≤1.00
Si (%) ≤0.40 ≤0.50
Cr (%) 11.00–13.00 15.5–17.5
Mo (%) 0.40–0.60 0.80–1.30
V (%) 0.15–0.30 Not specified
S (%) ≤0.030 Not specified
P (%) ≤0.030 Not specified
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GB/T 1299 Cr12MoV EN ISO 4957 1.2316
Hardness (annealed) ≤255 HB Not specified
Hardness (hardened) 57–62 HRC Not specified
Compressive Strength 2400 MPa Not specified
Hardness HRC Not specified 28–34 (pre-hardened)
Hardness HRC (hardened) Not specified 38–44
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
GB/T 1299 Cr12MoV
Blanking dies, forming dies, thread rolling dies, punches, shear blades, gauges, broaches, drawing dies
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can GB/T 1299 Cr12MoV Be Substituted With EN ISO 4957 1.2316?
GB/T 1299 Cr12MoV and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
GB/T 1299 Cr12MoV
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3100–3400 mm (122.05–133.86 in)
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
GB/T 1299 Cr12MoV
2 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between GB/T 1299 Cr12MoV and EN ISO 4957 1.2316?
GB/T 1299 Cr12MoV specifies V, S, P which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Ni which is not specified for GB/T 1299 Cr12MoV.
Can GB/T 1299 Cr12MoV be substituted with EN ISO 4957 1.2316?
GB/T 1299 Cr12MoV and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.