Post Stock Login Register

GB/T 1591 Q420C vs GB/T 1591 Q420NC

Close Alternative — 78.8% match based on chemical composition and mechanical property overlap.

GB/T 1591 Q420C (GB/T 1591:2018) and GB/T 1591 Q420NC (GB/T 1591:2018) are both steel grades. Both fall under the Structural Steel category. GB/T 1591 Q420C is typically used for general structure for engineering (plates, strips, bars and sections), while GB/T 1591 Q420NC is commonly used for general structure for engineering (plates, strips, bars and sections). GB/T 1591 Q420C is defined under Guobiao Standards (GB/T), originating from China, while GB/T 1591 Q420NC is defined under Guobiao Standards (GB/T), originating from China.

As per chemical composition, GB/T 1591 Q420C vs GB/T 1591 Q420NC is a 84.9% match. As per mechanical properties, the match is 66.7%. Combined, this makes them a close alternative overall at 78.8%.

Other Structural Steel Grades to Compare With GB/T 1591 Q420C:
GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W CSA G40.21 400A CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
84.9%
MECHANICAL MATCH
66.7%
OVERALL
78.8%
Specifications
Property GB/T 1591 Q420C GB/T 1591 Q420NC
Standard GB/T 1591:2018 GB/T 1591:2018
Category Structural Steel Structural Steel
C (%) <=0.20 <=0.20
Si (%) <=0.55 <=0.60
Mn (%) <=1.70 1.00-1.70
P (%) <=0.030 <=0.030
S (%) <=0.030 <=0.030
Nb (%) <=0.05 0.01-0.05
V (%) <=0.13 0.01-0.20
Ti (%) <=0.05 0.006-0.05
Cr (%) <=0.30 <=0.30
Ni (%) <=0.80 <=0.80
Cu (%) <=0.40 <=0.40
Mo (%) <=0.20 <=0.10
N (%) <=0.015 <=0.015
Al (%) Not specified >=0.015
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GB/T 1591 Q420C GB/T 1591 Q420NC
Tensile Strength 520-680 MPa 520-680 MPa
Yield Strength >=420 MPa >=420 MPa
Elongation >=20% >=19%
Condition Hot-rolled (as-rolled), nominal thickness or diameter up to 16 mm for yield; tensile strength for up to 100 mm; elongation longitudinal, up to 40 mm Normalized or normalizing rolled, nominal thickness or diameter up to 16 mm (tensile strength: up to 100 mm)
Typical Applications
GB/T 1591 Q420C
General structure for engineering (plates, strips, bars and sections)
GB/T 1591 Q420NC
General structure for engineering (plates, strips, bars and sections)
Key Differences
Can GB/T 1591 Q420C Be Substituted With GB/T 1591 Q420NC?
GB/T 1591 Q420C and GB/T 1591 Q420NC are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
GB/T 1591 Q420C
0 active listings and RFQs →
GB/T 1591 Q420NC
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between GB/T 1591 Q420C and GB/T 1591 Q420NC?
GB/T 1591 Q420NC specifies Al which is not specified for GB/T 1591 Q420C.
Can GB/T 1591 Q420C be substituted with GB/T 1591 Q420NC?
GB/T 1591 Q420C and GB/T 1591 Q420NC are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.