Post Stock Login Register

IS 11169 (Part 1) 16Ni4Cr3 vs EN 10028-2 10CrMo9-10

Minimal Match — 34.6% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 1) 16Ni4Cr3 (IS 11169 (Part 1):1984) and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. IS 11169 (Part 1) 16Ni4Cr3 is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1), while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes. IS 11169 (Part 1) 16Ni4Cr3 is defined under Bureau of Indian Standards (IS), originating from India, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 11169 (Part 1) 16Ni4Cr3 vs EN 10028-2 10CrMo9-10 is a 51.9% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 34.6%.

Frequently Compared With IS 11169 (Part 1) 16Ni4Cr3:
IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 UNI 11234 100Cr6 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 4) 10Mo6 NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 7) 10Mo6H IS 1570 (Part 4) 103Cr6 IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
51.9%
MECHANICAL MATCH
0%
OVERALL
34.6%
Specifications
Property IS 11169 (Part 1) 16Ni4Cr3 EN 10028-2 10CrMo9-10
Standard IS 11169 (Part 1):1984 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) 0.12-0.20 0.08-0.14
Si (%) 0.10-0.35 <=0.50
Mn (%) 0.60-1.00 0.40-0.80
Ni (%) 0.80-1.20 Not specified
Cr (%) 0.60-1.00 2.00-2.50
P (%) Not specified <=0.020
S (%) Not specified <=0.010
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Mo (%) Not specified 0.90-1.10
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 1) 16Ni4Cr3 EN 10028-2 10CrMo9-10
Core Tensile Strength >=850 MPa (30 mm) / >=800 MPa (60 mm) / >=750 MPa (90 mm) Not specified
Core Elongation >=12% (30 mm) Not specified
Hardness, annealed <=180 HB Not specified
Tensile Strength Not specified 480-630 MPa
Yield Strength Not specified >=310 MPa
Elongation Not specified >=18%
Condition Not specified Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
IS 11169 (Part 1) 16Ni4Cr3
Cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1)
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
Can IS 11169 (Part 1) 16Ni4Cr3 Be Substituted With EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 16Ni4Cr3 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
IS 11169 (Part 1) 16Ni4Cr3
0 active listings and RFQs →
EN 10028-2 10CrMo9-10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 1) 16Ni4Cr3 and EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 16Ni4Cr3 specifies Ni which is not specified for EN 10028-2 10CrMo9-10. EN 10028-2 10CrMo9-10 specifies P, S, N, Cu which are not specified for IS 11169 (Part 1) 16Ni4Cr3.
Can IS 11169 (Part 1) 16Ni4Cr3 be substituted with EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 16Ni4Cr3 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.