Post Stock Login Register

IS 11169 (Part 1) 16Ni8Cr6Mo2 vs IS 4367 16Ni8Cr6Mo2

Strong Match — 87.7% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 1) 16Ni8Cr6Mo2 (IS 11169 (Part 1):1984) and IS 4367 16Ni8Cr6Mo2 (IS 4367:1991) are both steel grades. Both fall under the Alloy Steel category. IS 11169 (Part 1) 16Ni8Cr6Mo2 is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1), while IS 4367 16Ni8Cr6Mo2 is commonly used for gears, camshafts, piston pins, splined shafts, aerospace and automotive case-hardened components.. IS 11169 (Part 1) 16Ni8Cr6Mo2 is defined under Bureau of Indian Standards (IS), originating from India, while IS 4367 16Ni8Cr6Mo2 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, IS 11169 (Part 1) 16Ni8Cr6Mo2 vs IS 4367 16Ni8Cr6Mo2 is a 98.3% match. As per mechanical properties, the match is 66.7%. Combined, this makes them a strong match overall at 87.7%.

Frequently Compared With IS 11169 (Part 1) 16Ni8Cr6Mo2:
IS 1570 (Part 4) 10Cr20Mo6 NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 105Cr5 IS 4367 10Cr9Mo10 IS 1570 (Part 4) 10Mo6 UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 7) 10Mo6H IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 07Cr4Mo6
Match Breakdown
CHEMISTRY MATCH
98.3%
MECHANICAL MATCH
66.7%
OVERALL
87.7%
Specifications
Property IS 11169 (Part 1) 16Ni8Cr6Mo2 IS 4367 16Ni8Cr6Mo2
Standard IS 11169 (Part 1):1984 IS 4367:1991
Category Alloy Steel Alloy Steel
C (%) 0.12-0.20 0.12-0.20
Si (%) 0.10-0.35 0.10-0.35
Mn (%) 0.40-0.70 0.40-0.70
Ni (%) 1.80-2.20 1.80-2.20
Cr (%) 1.40-1.70 1.40-1.70
Mo (%) 0.15-0.25 0.15-0.25
S (%) Not specified <=0.035
P (%) Not specified <=0.035
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 1) 16Ni8Cr6Mo2 IS 4367 16Ni8Cr6Mo2
Core Tensile Strength >=1350 MPa (30 mm) / >=1200 MPa (60 mm) / >=1150 MPa (90 mm) Not specified
Core Elongation >=9% (30 mm) Not specified
Hardness, annealed <=190 HB Not specified
Tensile Strength Not specified 1350 MPa min
Elongation Not specified >=9%
Izod Impact Not specified 35 J min
Hardness (soft annealed) Not specified <=229 HB
Condition Not specified Refined, quenched and stress relieved (core properties), ruling section up to 30 mm
Typical Applications
IS 11169 (Part 1) 16Ni8Cr6Mo2
Cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1)
IS 4367 16Ni8Cr6Mo2
Gears, camshafts, piston pins, splined shafts, aerospace and automotive case-hardened components.
Key Differences
Can IS 11169 (Part 1) 16Ni8Cr6Mo2 Be Substituted With IS 4367 16Ni8Cr6Mo2?
IS 11169 (Part 1) 16Ni8Cr6Mo2 and IS 4367 16Ni8Cr6Mo2 overlap closely enough on chemistry and mechanical properties that IS 4367 16Ni8Cr6Mo2 is often considered as a substitute for IS 11169 (Part 1) 16Ni8Cr6Mo2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
IS 11169 (Part 1) 16Ni8Cr6Mo2
No active listings currently.
IS 4367 16Ni8Cr6Mo2
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5200–6300 mm (204.72–248.03 in)
On M-EX Right Now
IS 11169 (Part 1) 16Ni8Cr6Mo2
0 active listings and RFQs →
IS 4367 16Ni8Cr6Mo2
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 1) 16Ni8Cr6Mo2 and IS 4367 16Ni8Cr6Mo2?
IS 4367 16Ni8Cr6Mo2 specifies S, P which are not specified for IS 11169 (Part 1) 16Ni8Cr6Mo2.
Can IS 11169 (Part 1) 16Ni8Cr6Mo2 be substituted with IS 4367 16Ni8Cr6Mo2?
IS 11169 (Part 1) 16Ni8Cr6Mo2 and IS 4367 16Ni8Cr6Mo2 overlap closely enough on chemistry and mechanical properties that IS 4367 16Ni8Cr6Mo2 is often considered as a substitute for IS 11169 (Part 1) 16Ni8Cr6Mo2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.