Minimal Match — 35% match
based on chemical composition and mechanical property overlap.
IS 11169 (Part 1) 40Ni14 (IS 11169 (Part 1):1984) and EN 10028-2 10CrMo9-10 (EN 10028-2:2017) are both steel grades.
Both fall under the Alloy Steel category.
IS 11169 (Part 1) 40Ni14 is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1), while EN 10028-2 10CrMo9-10 is commonly used for flat products for pressure purposes.
IS 11169 (Part 1) 40Ni14 is defined under Bureau of Indian Standards (IS), originating from India, while EN 10028-2 10CrMo9-10 is defined under European Standard (EN), originating from Europe.
As per chemical composition, IS 11169 (Part 1) 40Ni14 vs EN 10028-2 10CrMo9-10 is a 52.9% match.
Mechanical property data is not available for both grades, so this factor could not be scored.
Combined, this makes them a minimal match overall at 35%.
Frequently Compared With IS 11169 (Part 1) 40Ni14:
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
IS 11169 (Part 1) 40Ni14
EN 10028-2 10CrMo9-10
Hardness, annealed
<=190 HB
Not specified
Tensile Strength
Not specified
480-630 MPa
Yield Strength
Not specified
>=310 MPa
Elongation
Not specified
>=18%
Condition
Not specified
Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
IS 11169 (Part 1) 40Ni14
Cold heading and cold extrusion; the standard covers wires, wire rods and bars of 2 to 100 mm diameter (clause 1.1)
EN 10028-2 10CrMo9-10
Flat products for pressure purposes
Key Differences
IS 11169 (Part 1) 40Ni14 specifies Ni which is not specified for EN 10028-2 10CrMo9-10.
EN 10028-2 10CrMo9-10 specifies P, S, N, Cu which are not specified for IS 11169 (Part 1) 40Ni14.
Can IS 11169 (Part 1) 40Ni14 Be Substituted With EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 40Ni14 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
What is the difference between IS 11169 (Part 1) 40Ni14 and EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 40Ni14 specifies Ni which is not specified for EN 10028-2 10CrMo9-10. EN 10028-2 10CrMo9-10 specifies P, S, N, Cu which are not specified for IS 11169 (Part 1) 40Ni14.
Can IS 11169 (Part 1) 40Ni14 be substituted with EN 10028-2 10CrMo9-10?
IS 11169 (Part 1) 40Ni14 and EN 10028-2 10CrMo9-10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.