Post Stock Login Register

IS 11169 (Part 1) 20C13BT vs IS 1570 (Part 4) 35C8BT

Close Alternative — 72.3% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 1) 20C13BT (IS 11169 (Part 1):2022) and IS 1570 (Part 4) 35C8BT (IS 1570 (Part 4):1988) are both steel grades. Both fall under the Alloy Steel category. IS 11169 (Part 1) 20C13BT is defined under Bureau of Indian Standards (IS), originating from India, while IS 1570 (Part 4) 35C8BT is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, IS 11169 (Part 1) 20C13BT vs IS 1570 (Part 4) 35C8BT is a 72.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 72.3%.

Frequently Compared With IS 11169 (Part 1) 20C13BT:
UNI 11234 100Cr6 IS 11169 (Part 1) 10Ni5Cr4 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 10Cr9Mo10 IS 1570 (Part 4) 10Mo6 IS 1570 (Part 7) 10Mo6H IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5
Match Breakdown
CHEMISTRY MATCH
72.3%
MECHANICAL MATCH
No shared data
OVERALL
72.3%
Specifications
Property IS 11169 (Part 1) 20C13BT IS 1570 (Part 4) 35C8BT
Standard IS 11169 (Part 1):2022 IS 1570 (Part 4):1988
Category Alloy Steel Alloy Steel
B (%) 0.0008-0.005 0.0005-0.003
C (%) 0.17-0.23 0.31-0.36
Cr (%) <=0.30 0.10-0.30
Cu (%) <=0.25 Not specified
Mn (%) 1.10-1.40 0.60-1.00
P (%) <=0.025 Not specified
S (%) <=0.025 Not specified
Si (%) <=0.30 0.10-0.35
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 1) 20C13BT IS 1570 (Part 4) 35C8BT
Tensile Strength, cold drawn, annealed and skin passed (+AR+C+AC+LC) <=630 MPa (over 5 to 40 mm) Not specified
Typical Applications
IS 11169 (Part 1) 20C13BT
Cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex C)
IS 1570 (Part 4) 35C8BT
Not documented
Key Differences
Can IS 11169 (Part 1) 20C13BT Be Substituted With IS 1570 (Part 4) 35C8BT?
IS 11169 (Part 1) 20C13BT and IS 1570 (Part 4) 35C8BT are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
IS 11169 (Part 1) 20C13BT
0 active listings and RFQs →
IS 1570 (Part 4) 35C8BT
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 1) 20C13BT and IS 1570 (Part 4) 35C8BT?
IS 11169 (Part 1) 20C13BT specifies Cu, P, S which are not specified for IS 1570 (Part 4) 35C8BT.
Can IS 11169 (Part 1) 20C13BT be substituted with IS 1570 (Part 4) 35C8BT?
IS 11169 (Part 1) 20C13BT and IS 1570 (Part 4) 35C8BT are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.