IS 11169 (Part 1):2022 40Cr4Mo2 Steel: Specifications & Listings

IS 11169 (Part 1):2022 40Cr4Mo2: Cold heading quality alloy steel 40Cr4Mo2 to IS 11169 (Part 1):2022 for quenching and tempering after cold heading or cold extrusion, supplied as wire rod, bars or wire of 2 to 100 mm. It can be ordered with hardenability requirements (H).

Category: Alloy Steel
Grade Details
GradeIS 11169 (Part 1):2022 40Cr4Mo2
Standard IS 11169 (Part 1):2022
ApplicationsCold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex C)
Equivalent / Similar Grades
Grade Standard Region Live on M-EX
SAE J404 4140 SAE J404:2009 USA 16 listings, 17 RFQs →
JIS G4105 SCM440 JIS G4105:1979 Japan 0 listings, 3 RFQs →
Grade ComparisonCompare With a Specific Grade →
Grade Standard Match
IS 11169 (Part 1) 35Cr4Mo2 IS 11169 (Part 1):2022 Strong Match
GOST 4543 35XM GOST 4543-2016 Close Alternative
IS 11169 (Part 1) 41Cr3 IS 11169 (Part 1):2022 Close Alternative
SAE J404 8637 SAE J404:2009 Close Alternative
SAE J404 8640 SAE J404:2009 Close Alternative
SAE J404 8637 SAE J404:2000 Close Alternative
SAE J404 8640 SAE J404:2000 Close Alternative
SAE J404 8740 SAE J404:2009 Close Alternative
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Chemical Composition (%)
C Cr Cu Mn Mo Ni P S Si
0.38-0.43 0.80-1.10 <=0.35 0.75-1.00 0.15-0.25 <=0.25 <=0.030 <=0.040 0.15-0.35

More data from IS 11169 (Part 1):2022

From the standard
Other composition limits from the table notes and clauses
Values
Maximum unless a range is given (ladle analysis)
Ordered with hardenability
Small deviations from these limits are allowed (not for sulphur and phosphorus): up to 0.01 percent for carbon and the Table 1 values for other elements
Deoxidation
Aluminium killed (clause 6.2)
Elements not listed are not added intentionally without the purchaser's agreement, except those used to finish the heat.
Source: IS 11169 (Part 1):2022, Table C.2 and its notes, clause 6.2
Hardenability, end quench test (H) Hardness band
Hardness band (HRC, minimum to maximum) by distance from the quenched end (1/16 inch)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
20
22
24
26
28
30
32
Distance from quenched end (1/16 inch)123456789101112131415161820222426283032
Maximum, HRC606060595958585757565655555454535251494847464544
Minimum, HRC535352515150484744424039383736353433333232313130
Applies when ordered with the symbol H; otherwise for guidance only. Jominy test as per IS 3848, austenitizing at 850 ± 5 °C. Distances are in sixteenths of an inch (25.4/16 mm), as printed.
Source: IS 11169 (Part 1):2022, Table C.9

Active IS 11169 (Part 1):2022 40Cr4Mo2 Listings on M-EX (For Sale)

+ Create a Listing for this grade

No active IS 11169 (Part 1):2022 40Cr4Mo2 listings at this time.

Register for Alerts

Buyer RFQs for IS 11169 (Part 1):2022 40Cr4Mo2

+ Post an RFQ for this grade

No open buyer requirements for IS 11169 (Part 1):2022 40Cr4Mo2 at this time.

Register for Alerts