Post Stock Login Register

IS 11169 (Part 1) 45C7S3 vs BS 970 (Part 1) 080H46

Strong Match — 85% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 1) 45C7S3 (IS 11169 (Part 1):2022) and BS 970 (Part 1) 080H46 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Carbon Steel category. IS 11169 (Part 1) 45C7S3 is typically used for cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, annex c), while BS 970 (Part 1) 080H46 is commonly used for through hardening steel for mechanical and allied engineering purposes; supplied in the hardened and tempered conditions of table 6.. IS 11169 (Part 1) 45C7S3 is defined under Bureau of Indian Standards (IS), originating from India, while BS 970 (Part 1) 080H46 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, IS 11169 (Part 1) 45C7S3 vs BS 970 (Part 1) 080H46 is a 85% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 85%.

Frequently Compared With IS 11169 (Part 1) 45C7S3:
BS 970 (Part 1) 040A10 BS 970 (Part 3) 070M55 BS 970 (Part 1) 045A10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32 BS 970 (Part 1) 040A12 BS 970 (Part 3) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045M10
Match Breakdown
CHEMISTRY MATCH
85%
MECHANICAL MATCH
No shared data
OVERALL
85%
Specifications
Property IS 11169 (Part 1) 45C7S3 BS 970 (Part 1) 080H46
Standard IS 11169 (Part 1):2022 BS 970 (Part 1):1983
Category Carbon Steel Carbon Steel
C (%) 0.42-0.50 0.43-0.50
Cu (%) <=0.25 Not specified
Mn (%) 0.50-0.80 0.60-1.00
P (%) <=0.025 <=0.050
S (%) 0.020-0.035 <=0.050
Si (%) <=0.30 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 1) 45C7S3 BS 970 (Part 1) 080H46
Tensile Strength, annealed (+AC) <=600 MPa (over 5 to 40 mm) Not specified
Typical Applications
IS 11169 (Part 1) 45C7S3
Cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex C)
BS 970 (Part 1) 080H46
Through hardening steel for mechanical and allied engineering purposes; supplied in the hardened and tempered conditions of Table 6.
Key Differences
Can IS 11169 (Part 1) 45C7S3 Be Substituted With BS 970 (Part 1) 080H46?
IS 11169 (Part 1) 45C7S3 and BS 970 (Part 1) 080H46 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 1) 080H46 is often considered as a substitute for IS 11169 (Part 1) 45C7S3 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 11169 (Part 1) 45C7S3
0 active listings and RFQs →
BS 970 (Part 1) 080H46
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 1) 45C7S3 and BS 970 (Part 1) 080H46?
IS 11169 (Part 1) 45C7S3 specifies Cu, Si which are not specified for BS 970 (Part 1) 080H46.
Can IS 11169 (Part 1) 45C7S3 be substituted with BS 970 (Part 1) 080H46?
IS 11169 (Part 1) 45C7S3 and BS 970 (Part 1) 080H46 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 1) 080H46 is often considered as a substitute for IS 11169 (Part 1) 45C7S3 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.