Post Stock Login Register

IS 11169 (Part 2) X04Cr19Ni10 vs IS 11169 (Part 2) X04Cr18Ni11

Strong Match — 89.8% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X04Cr19Ni10 (IS 11169 (Part 2):2023) and IS 11169 (Part 2) X04Cr18Ni11 (IS 11169 (Part 2):2023) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X04Cr19Ni10 is typically used for cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, table 11), while IS 11169 (Part 2) X04Cr18Ni11 is commonly used for cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, table 11). IS 11169 (Part 2) X04Cr19Ni10 is defined under Bureau of Indian Standards (IS), originating from India, while IS 11169 (Part 2) X04Cr18Ni11 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, IS 11169 (Part 2) X04Cr19Ni10 vs IS 11169 (Part 2) X04Cr18Ni11 is a 84.7% match. As per mechanical properties, the match is 100%. Combined, this makes them a strong match overall at 89.8%.

Frequently Compared With IS 11169 (Part 2) X04Cr19Ni10:
GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H GOST 5632 12Kh13 ASTM A959 .- EN 10088-1 1.4006
Match Breakdown
CHEMISTRY MATCH
84.7%
MECHANICAL MATCH
100%
OVERALL
89.8%
Specifications
Property IS 11169 (Part 2) X04Cr19Ni10 IS 11169 (Part 2) X04Cr18Ni11
Standard IS 11169 (Part 2):2023 IS 11169 (Part 2):2023
Category Stainless Steel Stainless Steel
C (%) <=0.07 <=0.08
Cr (%) 17.5-19.5 17.0-19.0
Cu (%) <=1.00 Not specified
Mn (%) <=2.00 <=2.00
N (%) <=0.10 <=0.10
Ni (%) 8.0-10.5 10.5-13.0
P (%) <=0.045 <=0.045
S (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X04Cr19Ni10 IS 11169 (Part 2) X04Cr18Ni11
Reduction of Area, solution annealed (+AT) >=65% (over 5 to 50 mm) >=65% (over 5 to 50 mm)
Tensile Strength, solution annealed (+AT) <=650 MPa (over 5 to 50 mm) <=650 MPa (over 5 to 50 mm)
Typical Applications
IS 11169 (Part 2) X04Cr19Ni10
Cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, Table 11)
IS 11169 (Part 2) X04Cr18Ni11
Cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, Table 11)
Key Differences
Can IS 11169 (Part 2) X04Cr19Ni10 Be Substituted With IS 11169 (Part 2) X04Cr18Ni11?
IS 11169 (Part 2) X04Cr19Ni10 and IS 11169 (Part 2) X04Cr18Ni11 overlap closely enough on chemistry and mechanical properties that IS 11169 (Part 2) X04Cr18Ni11 is often considered as a substitute for IS 11169 (Part 2) X04Cr19Ni10 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 11169 (Part 2) X04Cr19Ni10
0 active listings and RFQs →
IS 11169 (Part 2) X04Cr18Ni11
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X04Cr19Ni10 and IS 11169 (Part 2) X04Cr18Ni11?
IS 11169 (Part 2) X04Cr19Ni10 specifies Cu which is not specified for IS 11169 (Part 2) X04Cr18Ni11.
Can IS 11169 (Part 2) X04Cr19Ni10 be substituted with IS 11169 (Part 2) X04Cr18Ni11?
IS 11169 (Part 2) X04Cr19Ni10 and IS 11169 (Part 2) X04Cr18Ni11 overlap closely enough on chemistry and mechanical properties that IS 11169 (Part 2) X04Cr18Ni11 is often considered as a substitute for IS 11169 (Part 2) X04Cr19Ni10 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.