Post Stock Login Register

IS 1570 (Part 4) 10Mo6 vs EN 10028-2 13CrMoSi5-5

Close Alternative — 74.6% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 4) 10Mo6 (IS 1570 (Part 4):1988) and EN 10028-2 13CrMoSi5-5 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. IS 1570 (Part 4) 10Mo6 is defined under Bureau of Indian Standards (IS), originating from India, while EN 10028-2 13CrMoSi5-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 4) 10Mo6 vs EN 10028-2 13CrMoSi5-5 is a 74.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 74.6%.

Frequently Compared With IS 1570 (Part 4) 10Mo6:
IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr6 GOST 4543 12HN3A IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 UNI 11234 100Cr6 IS 4367 10Cr9Mo10 IS 1570 (Part 7) 12Cr2Mo5V2H IS 4367 07Cr4Mo6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 7) 10Mo6H
Match Breakdown
CHEMISTRY MATCH
74.6%
MECHANICAL MATCH
No shared data
OVERALL
74.6%
Specifications
Property IS 1570 (Part 4) 10Mo6 EN 10028-2 13CrMoSi5-5
Standard IS 1570 (Part 4):1988 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) <=0.15 <=0.17
Si (%) 0.15-0.25 0.50-0.80
Mn (%) 0.40-0.70 0.40-0.65
Ni (%) <=0.30 <=0.30
Cr (%) <=0.25 1.00-1.50
Mo (%) 0.45-0.65 0.45-0.65
P (%) Not specified <=0.015
S (%) Not specified <=0.005
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 4) 10Mo6 EN 10028-2 13CrMoSi5-5
Tensile Strength Not specified 510-690 MPa
Yield Strength Not specified >=310 MPa
Elongation Not specified >=20%
Condition Not specified Usual delivery condition normalized and tempered (+NT), nominal thickness up to 60 mm; transverse direction, Yield Strength is ReH, Elongation is A
Typical Applications
IS 1570 (Part 4) 10Mo6
Not documented
EN 10028-2 13CrMoSi5-5
Flat products for pressure purposes
Key Differences
Can IS 1570 (Part 4) 10Mo6 Be Substituted With EN 10028-2 13CrMoSi5-5?
IS 1570 (Part 4) 10Mo6 and EN 10028-2 13CrMoSi5-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
IS 1570 (Part 4) 10Mo6
0 active listings and RFQs →
EN 10028-2 13CrMoSi5-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 4) 10Mo6 and EN 10028-2 13CrMoSi5-5?
EN 10028-2 13CrMoSi5-5 specifies P, S, N, Cu which are not specified for IS 1570 (Part 4) 10Mo6.
Can IS 1570 (Part 4) 10Mo6 be substituted with EN 10028-2 13CrMoSi5-5?
IS 1570 (Part 4) 10Mo6 and EN 10028-2 13CrMoSi5-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.