Post Stock Login Register

IS 1570 (Part 4) 31Ni10Cr3Mo6 vs IS 1570 (Part 4) 105Cr5

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 4) 31Ni10Cr3Mo6 (IS 1570 (Part 4):1988) and IS 1570 (Part 4) 105Cr5 (IS 1570 (Part 4):1988) are both steel grades. Both fall under the Alloy Steel category. IS 1570 (Part 4) 31Ni10Cr3Mo6 is defined under Bureau of Indian Standards (IS), originating from India, while IS 1570 (Part 4) 105Cr5 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, IS 1570 (Part 4) 31Ni10Cr3Mo6 vs IS 1570 (Part 4) 105Cr5 is a 64.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 1570 (Part 4) 31Ni10Cr3Mo6:
IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 10Cr20Mo6 NF A35-565 100C6 UNI 11234 100Cr6 GB/T 3077 12Cr2Ni4A IS 1570 (Part 4) 103Cr6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 7) 10Mo6H IS 1570 (Part 7) 12Cr4Mo5H IS 4367 07Cr4Mo6 IS 1570 (Part 4) 10Mo6
Match Breakdown
CHEMISTRY MATCH
64.3%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property IS 1570 (Part 4) 31Ni10Cr3Mo6 IS 1570 (Part 4) 105Cr5
Standard IS 1570 (Part 4):1988 IS 1570 (Part 4):1988
Category Alloy Steel Alloy Steel
C (%) 0.27-0.35 0.90-1.20
Si (%) 0.10-0.35 0.10-0.35
Mn (%) 0.40-0.70 0.40-0.80
Ni (%) 2.25-2.75 Not specified
Cr (%) 0.50-0.80 1.00-1.60
Mo (%) 0.40-0.70 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 4) 31Ni10Cr3Mo6 IS 1570 (Part 4) 105Cr5
Tensile Strength 1190-1340 MPa Not specified
Yield Strength >=930 MPa (0.2 % proof stress) Not specified
Elongation >=10% Not specified
Izod Impact >=35 J Not specified
Hardness 341-401 HBS (guidance only) Not specified
Condition Bars and forgings, hardened and tempered (oil hardened unless stated), limiting ruling section 63 mm Not specified
Key Differences
Can IS 1570 (Part 4) 31Ni10Cr3Mo6 Be Substituted With IS 1570 (Part 4) 105Cr5?
IS 1570 (Part 4) 31Ni10Cr3Mo6 and IS 1570 (Part 4) 105Cr5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
IS 1570 (Part 4) 31Ni10Cr3Mo6
0 active listings and RFQs →
IS 1570 (Part 4) 105Cr5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 4) 31Ni10Cr3Mo6 and IS 1570 (Part 4) 105Cr5?
IS 1570 (Part 4) 31Ni10Cr3Mo6 specifies Ni, Mo which are not specified for IS 1570 (Part 4) 105Cr5.
Can IS 1570 (Part 4) 31Ni10Cr3Mo6 be substituted with IS 1570 (Part 4) 105Cr5?
IS 1570 (Part 4) 31Ni10Cr3Mo6 and IS 1570 (Part 4) 105Cr5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.