Post Stock Login Register

IS 1570 (Part 6) 60T6 vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 6) 60T6 (IS 1570 (Part 6):1996) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. IS 1570 (Part 6) 60T6 is defined under Bureau of Indian Standards (IS), originating from India, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 6) 60T6 vs EN ISO 4957 1.2316 is a 53% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 1570 (Part 6) 60T6:
IS 1570 (Part 6) 133T3 IS 1570 (Part 6) 118T3 IS 1570 (Part 6) 55T8 IS 1570 (Part 6) 70T6 IS 1570 (Part 6) 75T6 IS 1570 (Part 6) 65T6 IS 1570 (Part 6) 50T8 DIN EN ISO 4957 1.2344 IS 1570 (Part 6) 70T3 DIN EN ISO 4957 1.2379 EN ISO 683-17 100Cr6 IS 3748 65T6
Match Breakdown
CHEMISTRY MATCH
53%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property IS 1570 (Part 6) 60T6 EN ISO 4957 1.2316
Standard IS 1570 (Part 6):1996 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 0.55-0.65 ≤0.06
Si (%) 0.10-0.35 ≤0.50
Mn (%) 0.50-0.80 ≤1.00
P (%) <=0.035 Not specified
S (%) <=0.035 Not specified
Cr (%) <=0.20 15.5–17.5
Cu (%) <=0.25 Not specified
Ni (%) <=0.25 0.80–1.50
Mo (%) Not specified 0.80–1.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 6) 60T6 EN ISO 4957 1.2316
Hardness HRC Not specified 28–34 (pre-hardened)
Hardness HRC (hardened) Not specified 38–44
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
IS 1570 (Part 6) 60T6
Not documented
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can IS 1570 (Part 6) 60T6 Be Substituted With EN ISO 4957 1.2316?
IS 1570 (Part 6) 60T6 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 1570 (Part 6) 60T6
No active listings currently.
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
IS 1570 (Part 6) 60T6
0 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 6) 60T6 and EN ISO 4957 1.2316?
IS 1570 (Part 6) 60T6 specifies P, S, Cu which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Mo which is not specified for IS 1570 (Part 6) 60T6.
Can IS 1570 (Part 6) 60T6 be substituted with EN ISO 4957 1.2316?
IS 1570 (Part 6) 60T6 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.