Post Stock Login Register

IS 1570 (Part 7) 25Cr2MoVH vs ASTM A240/A240M S42200

Related Material — 62.7% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 7) 25Cr2MoVH (IS 1570 (Part 7):1992) and ASTM A240/A240M S42200 (ASTM A240/A240M:2025) are both steel grades. IS 1570 (Part 7) 25Cr2MoVH is classified under Alloy Steel, while ASTM A240/A240M S42200 is classified under Stainless Steel — a different category, which is worth noting alongside the chemistry match below. IS 1570 (Part 7) 25Cr2MoVH is typically used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature, while ASTM A240/A240M S42200 is commonly used for pressure vessels and general applications (plate, sheet and strip). IS 1570 (Part 7) 25Cr2MoVH is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A240/A240M S42200 is defined under ASTM International, originating from United States.

As per chemical composition, IS 1570 (Part 7) 25Cr2MoVH vs ASTM A240/A240M S42200 is a 62.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 62.7%.

Frequently Compared With IS 1570 (Part 7) 25Cr2MoVH:
IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 4) 07Cr4Mo6 NF A35-565 100C6 IS 1570 (Part 7) 12Cr2Mo5V2H GB/T 3077 12Cr2Ni4A UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 7) 10Mo6H
Match Breakdown
CHEMISTRY MATCH
62.7%
MECHANICAL MATCH
No shared data
OVERALL
62.7%
Specifications
Property IS 1570 (Part 7) 25Cr2MoVH ASTM A240/A240M S42200
Standard IS 1570 (Part 7):1992 ASTM A240/A240M:2025
Category Alloy Steel Stainless Steel
C (%) 0.20-0.30 0.20-0.25
Si (%) 0.20-0.50 <=0.50
Mn (%) 0.30-0.60 0.50-1.00
P (%) <=0.030 <=0.025
S (%) <=0.025 <=0.025
Cr (%) 1.5-1.80 11.0-12.5
Ni (%) <=0.40 0.50-1.00
Mo (%) 0.90-1.20 0.90-1.25
V (%) 0.20-0.30 0.20-0.30
Cu (%) <=0.30 Not specified
W (%) Not specified 0.90-1.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 7) 25Cr2MoVH ASTM A240/A240M S42200
Tensile Strength >=630 MPa Not specified
Yield Strength >=420 MPa (0.2 % proof stress) Not specified
Elongation >=16% Not specified
Condition Forgings of turbine shafts, N+T, thickness up to 900 (first row of Table 3) Plate, sheet and strip; yield by 0.2 percent offset
Hardness Not specified <=248 HB
Typical Applications
IS 1570 (Part 7) 25Cr2MoVH
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
ASTM A240/A240M S42200
Pressure vessels and general applications (plate, sheet and strip)
Key Differences
Can IS 1570 (Part 7) 25Cr2MoVH Be Substituted With ASTM A240/A240M S42200?
IS 1570 (Part 7) 25Cr2MoVH and ASTM A240/A240M S42200 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
IS 1570 (Part 7) 25Cr2MoVH
0 active listings and RFQs →
ASTM A240/A240M S42200
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 7) 25Cr2MoVH and ASTM A240/A240M S42200?
Different category: IS 1570 (Part 7) 25Cr2MoVH is Alloy Steel, ASTM A240/A240M S42200 is Stainless Steel. IS 1570 (Part 7) 25Cr2MoVH specifies Cu which is not specified for ASTM A240/A240M S42200. ASTM A240/A240M S42200 specifies W which is not specified for IS 1570 (Part 7) 25Cr2MoVH.
Can IS 1570 (Part 7) 25Cr2MoVH be substituted with ASTM A240/A240M S42200?
IS 1570 (Part 7) 25Cr2MoVH and ASTM A240/A240M S42200 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.