Post Stock Login Register

IS 1570 C45 vs BS 970 (Part 3) 070M55

Strong Match — 87% match based on chemical composition and mechanical property overlap.

IS 1570 C45 (IS 1570:1961) and BS 970 (Part 3) 070M55 (BS 970 (Part 3):1991) are both steel grades. Both fall under the Carbon Steel category. IS 1570 C45 is typically used for shafts, gears, studs, bolts, axles, rollers, machinery parts, while BS 970 (Part 3) 070M55 is commonly used for used for springs, blades, wear plates, hand tools, shafts, and cutting components.. IS 1570 C45 is defined under Bureau of Indian Standards (IS), originating from India, while BS 970 (Part 3) 070M55 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, IS 1570 C45 vs BS 970 (Part 3) 070M55 is a 87% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 87%.

Frequently Compared With IS 1570 C45:
BS 970 (Part 1) 040A10 BS 970 (Part 1) 080A20 BS 970 (Part 1) 045A10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045M10 BS 970 (Part 1) 040A12 BS 970 (Part 1) 060A32 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10
Match Breakdown
CHEMISTRY MATCH
87%
MECHANICAL MATCH
No shared data
OVERALL
87%
Specifications
Property IS 1570 C45 BS 970 (Part 3) 070M55
Standard IS 1570:1961 BS 970 (Part 3):1991
Category Carbon Steel Carbon Steel
C (%) 0.40-0.50 0.50-0.60
Mn (%) 0.60-0.90 0.50-0.90
Si (%) 0.15-0.35 0.10-0.40
S (%) <=0.04 <=0.05
P (%) <=0.04 <=0.05
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 C45 BS 970 (Part 3) 070M55
Tensile Strength 630-710 MPa Not specified
Yield Strength >=347 MPa Not specified
Elongation >=15% Not specified
Hardness 170-229 HB Not specified
Typical Applications
IS 1570 C45
shafts, gears, studs, bolts, axles, rollers, machinery parts
BS 970 (Part 3) 070M55
Used for springs, blades, wear plates, hand tools, shafts, and cutting components.
Can IS 1570 C45 Be Substituted With BS 970 (Part 3) 070M55?
IS 1570 C45 and BS 970 (Part 3) 070M55 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 3) 070M55 is often considered as a substitute for IS 1570 C45 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
IS 1570 C45
Round Bar → (24 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 4500–6900 mm (177.17–271.65 in)
BS 970 (Part 3) 070M55
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 4800–5800 mm (188.98–228.35 in)
On M-EX Right Now
IS 1570 C45
24 active listings and RFQs →
BS 970 (Part 3) 070M55
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 C45 and BS 970 (Part 3) 070M55?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can IS 1570 C45 be substituted with BS 970 (Part 3) 070M55?
IS 1570 C45 and BS 970 (Part 3) 070M55 overlap closely enough on chemistry and mechanical properties that BS 970 (Part 3) 070M55 is often considered as a substitute for IS 1570 C45 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.