Post Stock Login Register

IS 2062 (Part 1) E275C vs AS/NZS 1595 C350

Close Alternative — 77% match based on chemical composition and mechanical property overlap.

IS 2062 (Part 1) E275C (IS 2062 (Part 1):2025) and AS/NZS 1595 C350 (AS/NZS 1595:1998) are both steel grades. Both fall under the Structural Steel category. IS 2062 (Part 1) E275C is typically used for structural work: welded, bolted and riveted structures and general engineering purposes, while AS/NZS 1595 C350 is commonly used for cold-rolled structural steel sheet; roll-forming, cold-formed structural sections, purlins. IS 2062 (Part 1) E275C is defined under Bureau of Indian Standards (IS), originating from India, while AS/NZS 1595 C350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, IS 2062 (Part 1) E275C vs AS/NZS 1595 C350 is a 98.9% match. As per mechanical properties, the match is 33.3%. Combined, this makes them a close alternative overall at 77%.

Frequently Compared With IS 2062 (Part 1) E275C:
IS 2062 (Part 1) E235BR IS 2062 (Part 1) E235A IS 2062 (Part 1) E235C IS 2062 (Part 1) E235B0 GOST 19281 09G2S CSA G40.21 260W CSA G40.21 350W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 400A CSA G40.21 400W
Match Breakdown
CHEMISTRY MATCH
98.9%
MECHANICAL MATCH
33.3%
OVERALL
77%
Specifications
Property IS 2062 (Part 1) E275C AS/NZS 1595 C350
Standard IS 2062 (Part 1):2025 AS/NZS 1595:1998
Category Structural Steel Structural Steel
C (%) <=0.20 <=0.20
Mn (%) <=1.50 <=1.50
Si (%) <=0.40 <=0.50
S (%) <=0.040 <=0.040
P (%) <=0.040 <=0.040
CEV (%) <=0.41 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 2062 (Part 1) E275C AS/NZS 1595 C350
Tensile Strength >=430 MPa 430 MPa min
Yield Strength 275 MPa (<=16mm) / 265 MPa (16-40mm) / 255 MPa (40-100mm) / 225 MPa (>100mm) 350 MPa min
Elongation >=23% (<=40mm) / >=22% (40-63mm) / >=21% (63-100mm) / >=19% (>100mm) 14% min
Impact Energy >=27 J at -20°C Not specified
Typical Applications
IS 2062 (Part 1) E275C
Structural work: welded, bolted and riveted structures and general engineering purposes
AS/NZS 1595 C350
Cold-rolled structural steel sheet; roll-forming, cold-formed structural sections, purlins
Key Differences
Can IS 2062 (Part 1) E275C Be Substituted With AS/NZS 1595 C350?
IS 2062 (Part 1) E275C and AS/NZS 1595 C350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
IS 2062 (Part 1) E275C
No active listings currently.
AS/NZS 1595 C350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–4600 mm (98.43–181.1 in)
On M-EX Right Now
IS 2062 (Part 1) E275C
0 active listings and RFQs →
AS/NZS 1595 C350
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 2062 (Part 1) E275C and AS/NZS 1595 C350?
IS 2062 (Part 1) E275C specifies CEV which is not specified for AS/NZS 1595 C350.
Can IS 2062 (Part 1) E275C be substituted with AS/NZS 1595 C350?
IS 2062 (Part 1) E275C and AS/NZS 1595 C350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.