Post Stock Login Register

IS 2062 E450E vs AS/NZS 3679.1 350

Close Alternative — 76.8% match based on chemical composition and mechanical property overlap.

IS 2062 E450E (IS 2062:2006) and AS/NZS 3679.1 350 (AS/NZS 3679.1:2016) are both steel grades. Both fall under the Structural Steel category. IS 2062 E450E is typically used for structural work: welded, bolted and riveted structures and general engineering purposes, while AS/NZS 3679.1 350 is commonly used for hot-rolled structural bars and sections for primary structural beams, columns, and framing. IS 2062 E450E is defined under Bureau of Indian Standards (IS), originating from India, while AS/NZS 3679.1 350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, IS 2062 E450E vs AS/NZS 3679.1 350 is a 98.5% match. As per mechanical properties, the match is 33.3%. Combined, this makes them a close alternative overall at 76.8%.

Frequently Compared With IS 2062 E450E:
GOST 19281 09G2S CSA G40.21 480W ASTM A1008 SS Grade 50 CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W CSA G40.21 350W CSA G40.21 400A CSA G40.21 400W ASTM A1008 SS Grade 80 ASTM A283C ASTM A572 Gr.65
Match Breakdown
CHEMISTRY MATCH
98.5%
MECHANICAL MATCH
33.3%
OVERALL
76.8%
Specifications
Property IS 2062 E450E AS/NZS 3679.1 350
Standard IS 2062:2006 AS/NZS 3679.1:2016
Category Structural Steel Structural Steel
C (%) <=0.22 <=0.22
Mn (%) <=1.80 <=1.70
S (%) <=0.045 <=0.040
P (%) <=0.045 <=0.040
Si (%) <=0.45 <=0.50
CEV (%) <=0.48 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 2062 E450E AS/NZS 3679.1 350
Tensile Strength >=590 MPa 480-640 MPa
Yield Strength 450 MPa (<20mm) / 430 MPa (20-40mm) / 420 MPa (>40mm) 350 MPa min
Elongation >=20% 20% min
Impact Energy >=45 J at room temperature (25 +/- 2°C) / >=20 J at -20°C Not specified
Typical Applications
IS 2062 E450E
Structural work: welded, bolted and riveted structures and general engineering purposes
AS/NZS 3679.1 350
Hot-rolled structural bars and sections for primary structural beams, columns, and framing
Key Differences
Can IS 2062 E450E Be Substituted With AS/NZS 3679.1 350?
IS 2062 E450E and AS/NZS 3679.1 350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
IS 2062 E450E
No active listings currently.
AS/NZS 3679.1 350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–3200 mm (114.17–125.98 in)
On M-EX Right Now
IS 2062 E450E
0 active listings and RFQs →
AS/NZS 3679.1 350
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 2062 E450E and AS/NZS 3679.1 350?
IS 2062 E450E specifies CEV which is not specified for AS/NZS 3679.1 350.
Can IS 2062 E450E be substituted with AS/NZS 3679.1 350?
IS 2062 E450E and AS/NZS 3679.1 350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.