Post Stock Login Register

IS 3195 98C6 vs EN 10089 50CrV4

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 3195 98C6 (IS 3195:1992) and EN 10089 50CrV4 (EN 10089:2002) are both steel grades. Both fall under the Spring Steel category. IS 3195 98C6 is typically used for volute and helical springs for railway rolling stock; flats and rounds, springs worked hot and heat-treated (clause 1.1, foreword), while EN 10089 50CrV4 is commonly used for valve springs, high duty coil springs, hand tools. IS 3195 98C6 is defined under Bureau of Indian Standards (IS), originating from India, while EN 10089 50CrV4 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 3195 98C6 vs EN 10089 50CrV4 is a 73.1% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 3195 98C6:
IS 3195 113C6 IS 3195 50Cr4V2 IS 3195 52Cr4Mo2V IS 1570 (Part 4) 60Si7 IS 5517 55Cr3 EN 10089 55Cr3 IS 1570 (Part 4) 65Si7 IS 3431 50Cr4V2 EN 10083-3 51CrV4 IS 1570 (Part 4) 55Si7 BS 970 EN42D GB/T 1222 55CrMnA
Match Breakdown
CHEMISTRY MATCH
73.1%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property IS 3195 98C6 EN 10089 50CrV4
Standard IS 3195:1992 EN 10089:2002
Category Spring Steel Spring Steel
C (%) 0.90-1.05 0.47–0.55
Mn (%) 0.50-0.80 0.70–1.10
P (%) <=0.050 Not specified
S (%) <=0.050 Not specified
Si (%) 0.15-0.35 0.15–0.35
Cr (%) Not specified 0.90–1.20
V (%) Not specified 0.10–0.20
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 3195 98C6 EN 10089 50CrV4
Hardness, annealed <=240 HB Not specified
Tensile Strength Not specified 1100–1300 MPa
Yield Strength Not specified ≥1000 MPa
Elongation Not specified ≥8%
Hardness Not specified 321–375 HB
Typical Applications
IS 3195 98C6
Volute and helical springs for railway rolling stock; flats and rounds, springs worked hot and heat-treated (clause 1.1, foreword)
EN 10089 50CrV4
Valve springs, high duty coil springs, hand tools
Key Differences
Can IS 3195 98C6 Be Substituted With EN 10089 50CrV4?
IS 3195 98C6 and EN 10089 50CrV4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 3195 98C6
No active listings currently.
EN 10089 50CrV4
Round Bar → (3 listings)
Diameter: 30–30 mm (1.18–1.18 in)
Length: 5000–6500 mm (196.85–255.91 in)
On M-EX Right Now
IS 3195 98C6
0 active listings and RFQs →
EN 10089 50CrV4
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 3195 98C6 and EN 10089 50CrV4?
IS 3195 98C6 specifies P, S which are not specified for EN 10089 50CrV4. EN 10089 50CrV4 specifies Cr, V which are not specified for IS 3195 98C6.
Can IS 3195 98C6 be substituted with EN 10089 50CrV4?
IS 3195 98C6 and EN 10089 50CrV4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.