Post Stock Login Register

IS 3748 80T3 vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 3748 80T3 (IS 3748:1990) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. IS 3748 80T3 is typically used for cold work tools and dies for blanking, trimming, chipping and shearing, while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. IS 3748 80T3 is defined under Bureau of Indian Standards (IS), originating from India, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 3748 80T3 vs EN ISO 4957 1.2316 is a 55.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 3748 80T3:
IS 3748 118T3 IS 3748 70T3 DIN EN ISO 4957 1.2344 IS 3748 133T3 EN ISO 683-17 100Cr6 IS 3748 103T3 IS 1570 (Part 6) 103T3 IS 1570 (Part 6) 118T3 IS 1570 (Part 6) 133T3 GB/T 1299 3Cr2W8V GOST 5950 3H2W8F IS 3748 75T6
Match Breakdown
CHEMISTRY MATCH
55.8%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property IS 3748 80T3 EN ISO 4957 1.2316
Standard IS 3748:1990 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 0.75-0.85 ≤0.06
Si (%) 0.10-0.30 ≤0.50
Mn (%) <=0.40 ≤1.00
S (%) <=0.035 Not specified
P (%) <=0.035 Not specified
Cr (%) Not specified 15.5–17.5
Mo (%) Not specified 0.80–1.30
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 3748 80T3 EN ISO 4957 1.2316
Hardness <=220 HB Not specified
Condition Annealed (maximum Brinell hardness) Not specified
Hardness HRC Not specified 28–34 (pre-hardened)
Hardness HRC (hardened) Not specified 38–44
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
IS 3748 80T3
Cold work tools and dies for blanking, trimming, chipping and shearing
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can IS 3748 80T3 Be Substituted With EN ISO 4957 1.2316?
IS 3748 80T3 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 3748 80T3
No active listings currently.
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
IS 3748 80T3
0 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 3748 80T3 and EN ISO 4957 1.2316?
IS 3748 80T3 specifies S, P which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Cr, Mo, Ni which are not specified for IS 3748 80T3.
Can IS 3748 80T3 be substituted with EN ISO 4957 1.2316?
IS 3748 80T3 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.