Post Stock Login Register

IS 3748 90T3 vs IS 1570 (Part 6) 103T3

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 3748 90T3 (IS 3748:1990) and IS 1570 (Part 6) 103T3 (IS 1570 (Part 6):1996) are both steel grades. Both fall under the Tool & Die Steels category. IS 3748 90T3 is defined under Bureau of Indian Standards (IS), originating from India, while IS 1570 (Part 6) 103T3 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, IS 3748 90T3 vs IS 1570 (Part 6) 103T3 is a 77.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 3748 90T3:
IS 3748 103T3 GOST 5950 3H2W8F EN ISO 4957 1.2316 DIN EN ISO 4957 1.2344 DIN EN ISO 4957 1.2379 EN ISO 683-17 100Cr6 IS 3748 118T3 IS 1570 (Part 6) 118T3 IS 3748 133T3 IS 1570 (Part 6) 133T3 GB/T 1299 3Cr2W8V GB/T 1299 4Cr5MoSiV
Match Breakdown
CHEMISTRY MATCH
77.2%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property IS 3748 90T3 IS 1570 (Part 6) 103T3
Standard IS 3748:1990 IS 1570 (Part 6):1996
Category Tool & Die Steels Tool & Die Steels
C (%) 0.85-0.95 0.95-1.10
Si (%) 0.10-0.30 0.10-0.30
Mn (%) <=0.40 <=0.40
S (%) <=0.035 <=0.035
P (%) <=0.035 <=0.035
Cr (%) Not specified <=0.20
Cu (%) Not specified <=0.25
Ni (%) Not specified <=0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 3748 90T3 IS 1570 (Part 6) 103T3
Hardness <=220 HB Not specified
Condition Annealed (maximum Brinell hardness) Not specified
Typical Applications
IS 3748 90T3
Cold work tools and dies for blanking, trimming, chipping and shearing
IS 1570 (Part 6) 103T3
Not documented
Key Differences
Can IS 3748 90T3 Be Substituted With IS 1570 (Part 6) 103T3?
IS 3748 90T3 and IS 1570 (Part 6) 103T3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
IS 3748 90T3
0 active listings and RFQs →
IS 1570 (Part 6) 103T3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 3748 90T3 and IS 1570 (Part 6) 103T3?
IS 1570 (Part 6) 103T3 specifies Cr, Cu, Ni which are not specified for IS 3748 90T3.
Can IS 3748 90T3 be substituted with IS 1570 (Part 6) 103T3?
IS 3748 90T3 and IS 1570 (Part 6) 103T3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.