Post Stock Login Register

IS 6603 X02Cr25Ni6Mo3CuN vs EN 10088-1 X2CrNiMoCuN25-6-3

Strong Match — 91.2% match based on chemical composition and mechanical property overlap.

IS 6603 X02Cr25Ni6Mo3CuN (IS 6603:2024) and EN 10088-1 X2CrNiMoCuN25-6-3 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. IS 6603 X02Cr25Ni6Mo3CuN is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 X2CrNiMoCuN25-6-3 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 6603 X02Cr25Ni6Mo3CuN vs EN 10088-1 X2CrNiMoCuN25-6-3 is a 91.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 91.2%.

Frequently Compared With IS 6603 X02Cr25Ni6Mo3CuN:
EN 10088-1 1.4301 EN 10088-1 1.4845 ASTM A959 255 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH ASTM A959 .- GB/T 3280 06Cr19Ni10
Match Breakdown
CHEMISTRY MATCH
91.2%
MECHANICAL MATCH
No shared data
OVERALL
91.2%
Specifications
Property IS 6603 X02Cr25Ni6Mo3CuN EN 10088-1 X2CrNiMoCuN25-6-3
Standard IS 6603:2024 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=0.70 <=0.70
Mn (%) <=2.00 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.015 <=0.015
Cr (%) 24.0-26.0 24.0-26.0
Mo (%) 2.5-4.0 3.0-4.0
Ni (%) 5.0-7.5 6.0-8.0
N (%) 0.15-0.30 0.20-0.30
Cu (%) 1.00-2.50 1.00-2.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 6603 X02Cr25Ni6Mo3CuN EN 10088-1 X2CrNiMoCuN25-6-3
Tensile Strength >=700 MPa Not specified
Yield Strength >=500 MPa Not specified
Elongation >=25% Not specified
Hardness <=270 HB Not specified
Condition Solution annealed, conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Tensile Strength is a minimum as printed, hardness for guidance only Not specified
Typical Applications
IS 6603 X02Cr25Ni6Mo3CuN
General purposes, semi-finished products, bars, wire rods and bright bars
EN 10088-1 X2CrNiMoCuN25-6-3
Not documented
Can IS 6603 X02Cr25Ni6Mo3CuN Be Substituted With EN 10088-1 X2CrNiMoCuN25-6-3?
IS 6603 X02Cr25Ni6Mo3CuN and EN 10088-1 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMoCuN25-6-3 is often considered as a substitute for IS 6603 X02Cr25Ni6Mo3CuN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 6603 X02Cr25Ni6Mo3CuN
0 active listings and RFQs →
EN 10088-1 X2CrNiMoCuN25-6-3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 6603 X02Cr25Ni6Mo3CuN and EN 10088-1 X2CrNiMoCuN25-6-3?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can IS 6603 X02Cr25Ni6Mo3CuN be substituted with EN 10088-1 X2CrNiMoCuN25-6-3?
IS 6603 X02Cr25Ni6Mo3CuN and EN 10088-1 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMoCuN25-6-3 is often considered as a substitute for IS 6603 X02Cr25Ni6Mo3CuN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.