IS 6911:1992 X07Cr18Ni9 Steel: Specifications & Listings

IS 6911:1992 X07Cr18Ni9: Austenitic stainless steel X07Cr18Ni9 (numerical symbol 302) to IS 6911:1992 (reaffirmed 1998), made as plate, sheet and strip and normally supplied solution annealed and descaled. Minimum tensile strength annealed is 400 MPa with 0.2% proof stress of 210 MPa.

Category: Stainless Steel
Grade Details
GradeIS 6911:1992 X07Cr18Ni9
Standard IS 6911:1992
ApplicationsStainless and heat-resisting steel plate, sheet and strip (clause 1.1)
Equivalent / Similar Grades
Grade Standard Region Live on M-EX
IS 1570 (Part 5) X07Cr18Ni9 IS 1570 (Part 5):1985 India No activity yet
ASTM A959 302 ASTM A959:2011 USA No activity yet
ASTM A959 303 ASTM A959:2011 USA No activity yet
ASTM A959 303Se ASTM A959:2011 USA No activity yet
BS 970 (Part 3) 302S31 BS 970 (Part 3):1991 UK No activity yet
BS 970 (Part 3) 303S31 BS 970 (Part 3):1991 UK No activity yet
BS 970 (Part 3) 303S42 BS 970 (Part 3):1991 UK No activity yet
BS 970 (Part 3) 325S31 BS 970 (Part 3):1991 UK No activity yet
EN 10088-1 X9CrNi18-9 EN 10088-1:2014 Europe (CEN) No activity yet
Grade ComparisonCompare With a Specific Grade →
Grade Standard Match
BS 970 (Part 3) 302S31 BS 970 (Part 3):1991 Strong Match
BS 970 (Part 1) 302S31 BS 970 (Part 1):1983 Strong Match
EN 10088-1 X9CrNi18-9 EN 10088-1:2014 Strong Match
EN 10088-1 X9CrNi18-9 EN 10088-1:2023 Strong Match
ASTM A959 302 ASTM A959:2011 Strong Match
ASTM A959 303Se ASTM A959:2011 Strong Match
BS 970 (Part 3) 303S42 BS 970 (Part 3):1991 Strong Match
ASTM A959 303 ASTM A959:2011 Strong Match
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Chemical Composition (%)
C Cr Mn Ni P S Si
<=0.15 17.0-19.0 <=2.0 8.0-10.0 <=0.045 <=0.030 <=1.0
Mechanical Properties
Bend Test (180 deg) Not required
Elongation (50 mm, annealed) >=40%
Hardness (annealed, max) 192 HBS, 92 HRB
Tensile Strength (annealed) >=400 MPa
Yield Strength (0.2% proof, annealed) >=210 MPa

More data from IS 6911:1992

From the standard
Other composition limits from Table 1 and its note
Steel type
Austenitic
Numerical symbol (ISS)
302
Values
Maximum unless a range is given (ladle analysis)
Element not specified, Titanium, max
0.10
Element not specified, Niobium, max
0.20
Element not specified, Molybdenum, max
0.70
Element not specified, Copper, max
0.50
Elements not listed in Table 1 are not added to the steel except to finish the heat, and then only within the limits shown.
Source: IS 6911:1992, Table 1 and its note
Recommended heat treatment Table 3
TreatmentTemperature (deg C)Cooling medium
Softening (solution annealing), S1 000 to 1 120water or oil or air
Recommended heat treatment (clause 8.3). Austenitic steels are supplied solution annealed and descaled; ferritic and martensitic steels annealed and descaled, unless agreed otherwise.
Source: IS 6911:1992, Table 3
Properties in work hardened condition Table 6
0.2% proof stress, min (MPa)Tensile strength, min (MPa)Elongation, min (%)Up to thickness (mm)
490830122.8
7401 03092.4
Cold rolled (work hardened) supply by agreement between purchaser and supplier (clause 10.5). Elongation on a gauge length of 5.65 times the square root of the cross section.
Source: IS 6911:1992, Table 6

Active IS 6911:1992 X07Cr18Ni9 Listings on M-EX (For Sale)

+ Create a Listing for this grade

No active IS 6911:1992 X07Cr18Ni9 listings at this time.

Register for Alerts

Buyer RFQs for IS 6911:1992 X07Cr18Ni9

+ Post an RFQ for this grade

No open buyer requirements for IS 6911:1992 X07Cr18Ni9 at this time.

Register for Alerts