Post Stock Login Register

JIS G4304 SUS317J1 vs EN 10088-1 X2CrNiMoN17-13-5

Close Alternative — 74.6% match based on chemical composition and mechanical property overlap.

JIS G4304 SUS317J1 (JIS G4304:2021) and EN 10088-1 X2CrNiMoN17-13-5 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. JIS G4304 SUS317J1 is defined under Japanese Industrial Standards (JIS), originating from Japan, while EN 10088-1 X2CrNiMoN17-13-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, JIS G4304 SUS317J1 vs EN 10088-1 X2CrNiMoN17-13-5 is a 74.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 74.6%.

Frequently Compared With JIS G4304 SUS317J1:
IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
74.6%
MECHANICAL MATCH
No shared data
OVERALL
74.6%
Specifications
Property JIS G4304 SUS317J1 EN 10088-1 X2CrNiMoN17-13-5
Standard JIS G4304:2021 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) <=0.040 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) <=2.50 <=2.00
P (%) <=0.045 <=0.045
S (%) <=0.030 <=0.015
Ni (%) 15.00-17.00 12.5-14.5
Cr (%) 16.00-19.00 16.5-18.5
Mo (%) 4.00-6.00 4.0-5.0
N (%) Not specified 0.12-0.22
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4304 SUS317J1 EN 10088-1 X2CrNiMoN17-13-5
Tensile Strength >=480 MPa Not specified
Yield Strength >=175 MPa Not specified
Elongation >=40% Not specified
Hardness <=187 HB Not specified
Condition Solution heat treated plate and strip; 0.2 percent proof strength applies only when specified by the purchaser Not specified
Typical Applications
JIS G4304 SUS317J1
Hot-rolled stainless steel plates and strips
EN 10088-1 X2CrNiMoN17-13-5
Not documented
Key Differences
Can JIS G4304 SUS317J1 Be Substituted With EN 10088-1 X2CrNiMoN17-13-5?
JIS G4304 SUS317J1 and EN 10088-1 X2CrNiMoN17-13-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
JIS G4304 SUS317J1
0 active listings and RFQs →
EN 10088-1 X2CrNiMoN17-13-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4304 SUS317J1 and EN 10088-1 X2CrNiMoN17-13-5?
EN 10088-1 X2CrNiMoN17-13-5 specifies N which is not specified for JIS G4304 SUS317J1.
Can JIS G4304 SUS317J1 be substituted with EN 10088-1 X2CrNiMoN17-13-5?
JIS G4304 SUS317J1 and EN 10088-1 X2CrNiMoN17-13-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.