Post Stock Login Register

JIS G4305 SUS445J1 vs EN 10088-1 1.4006

Minimal Match — 34.9% match based on chemical composition and mechanical property overlap.

JIS G4305 SUS445J1 (JIS G4305:2012) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. JIS G4305 SUS445J1 is typically used for cold-rolled stainless steel plates, sheet and strip, while EN 10088-1 1.4006 is commonly used for cutlery, turbine blades, fasteners, surgical instruments. JIS G4305 SUS445J1 is defined under Japanese Industrial Standards (JIS), originating from Japan, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, JIS G4305 SUS445J1 vs EN 10088-1 1.4006 is a 52.4% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 34.9%.

Frequently Compared With JIS G4305 SUS445J1:
GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12Ni2Mo ASTM A959 .- GOST 5632 08X18H10 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
52.4%
MECHANICAL MATCH
0%
OVERALL
34.9%
Specifications
Property JIS G4305 SUS445J1 EN 10088-1 1.4006
Standard JIS G4305:2012 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.025 0.08–0.15
Si (%) <=1.00 ≤1.00
Mn (%) <=1.00 ≤1.50
P (%) <=0.040 Not specified
S (%) <=0.030 Not specified
Cr (%) 21.00-24.00 11.5–13.5
Mo (%) 0.70-1.50 Not specified
N (%) <=0.025 Not specified
Ni (%) <=0.60 ≤0.75
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4305 SUS445J1 EN 10088-1 1.4006
Tensile Strength >=410 MPa ≥540 MPa (annealed)
Yield Strength >=245 MPa Not specified
Elongation >=20% ≥18%
Hardness <=217 HB Not specified
Condition Annealed plate and strip; proof strength applies only when specified by the purchaser Not specified
Hardness HRC Not specified 36–45 (hardened)
Typical Applications
JIS G4305 SUS445J1
Cold-rolled stainless steel plates, sheet and strip
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can JIS G4305 SUS445J1 Be Substituted With EN 10088-1 1.4006?
JIS G4305 SUS445J1 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
JIS G4305 SUS445J1
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
JIS G4305 SUS445J1
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4305 SUS445J1 and EN 10088-1 1.4006?
JIS G4305 SUS445J1 specifies P, S, Mo, N which are not specified for EN 10088-1 1.4006.
Can JIS G4305 SUS445J1 be substituted with EN 10088-1 1.4006?
JIS G4305 SUS445J1 and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.