Post Stock Login Register

JIS G4404 SKD6 vs IS 1570 (Part 6) XT35Cr5MoV1

Close Alternative — 84.2% match based on chemical composition and mechanical property overlap.

JIS G4404 SKD6 (JIS G4404:2006) and IS 1570 (Part 6) XT35Cr5MoV1 (IS 1570 (Part 6):1996) are both steel grades. Both fall under the Tool & Die Steels category. JIS G4404 SKD6 is defined under Japanese Industrial Standards (JIS), originating from Japan, while IS 1570 (Part 6) XT35Cr5MoV1 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, JIS G4404 SKD6 vs IS 1570 (Part 6) XT35Cr5MoV1 is a 84.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 84.2%.

Frequently Compared With JIS G4404 SKD6:
GOST 5950 4H5MFS1 GOST 5950 4H5MFS EN ISO 683-17 100Cr6 AISI 52100 GB/T 1299 4Cr5MoSiV EN ISO 4957 1.2316 GOST 5950 3H2W8F GB/T 1299 3Cr2W8V DIN EN ISO 4957 1.2344 DIN EN ISO 4957 1.2379 GB/T 1299 4Cr5MoSiV1 IS 1570 (Part 6) 103T3
Match Breakdown
CHEMISTRY MATCH
84.2%
MECHANICAL MATCH
No shared data
OVERALL
84.2%
Specifications
Property JIS G4404 SKD6 IS 1570 (Part 6) XT35Cr5MoV1
Standard JIS G4404:2006 IS 1570 (Part 6):1996
Category Tool & Die Steels Tool & Die Steels
C (%) 0.32-0.42 0.30-0.40
Si (%) 0.80-1.20 0.80-1.20
Mn (%) 0.25-0.50 0.25-0.50
Cr (%) 4.50-5.50 4.75-5.50
Mo (%) 1.00-1.50 1.20-1.60
V (%) 0.30-0.50 1.00-1.20
P (%) Not specified <=0.035
S (%) Not specified <=0.035
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4404 SKD6 IS 1570 (Part 6) XT35Cr5MoV1
Hardness HRC (hardened) 40-52 Not specified
Hardness HB (annealed) <=229 Not specified
Typical Applications
JIS G4404 SKD6
Die casting dies, hot forging tools
IS 1570 (Part 6) XT35Cr5MoV1
Not documented
Key Differences
Can JIS G4404 SKD6 Be Substituted With IS 1570 (Part 6) XT35Cr5MoV1?
JIS G4404 SKD6 and IS 1570 (Part 6) XT35Cr5MoV1 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
JIS G4404 SKD6
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2500–3900 mm (98.43–153.54 in)
IS 1570 (Part 6) XT35Cr5MoV1
No active listings currently.
On M-EX Right Now
JIS G4404 SKD6
2 active listings and RFQs →
IS 1570 (Part 6) XT35Cr5MoV1
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4404 SKD6 and IS 1570 (Part 6) XT35Cr5MoV1?
IS 1570 (Part 6) XT35Cr5MoV1 specifies P, S which are not specified for JIS G4404 SKD6.
Can JIS G4404 SKD6 be substituted with IS 1570 (Part 6) XT35Cr5MoV1?
JIS G4404 SKD6 and IS 1570 (Part 6) XT35Cr5MoV1 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.