Post Stock Login Register

JIS G4805 SUJ2 vs EN ISO 4957 1.2316

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

JIS G4805 SUJ2 (JIS G 4805:1999) and EN ISO 4957 1.2316 (EN ISO 4957:2018) are both steel grades. Both fall under the Tool & Die Steels category. JIS G4805 SUJ2 is typically used for ball bearings, roller bearings, bearing races, precision rolls, while EN ISO 4957 1.2316 is commonly used for plastic injection moulds for corrosive materials, food packaging moulds. JIS G4805 SUJ2 is defined under Japanese Industrial Standards (JIS), originating from Japan, while EN ISO 4957 1.2316 is defined under European Standard (EN), originating from Europe.

As per chemical composition, JIS G4805 SUJ2 vs EN ISO 4957 1.2316 is a 62.2% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With JIS G4805 SUJ2:
EN ISO 683-17 100Cr6 AISI 52100 GOST 5950 4H5MFS1 GB/T 1299 4Cr5MoSiV1 GOST 5950 3H2W8F GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS DIN EN ISO 4957 1.2344 DIN EN ISO 4957 1.2379 GB/T 1299 3Cr2W8V IS 1570 (Part 6) 103T3
Other Tool & Die Steels Grades to Compare With JIS G4805 SUJ2:
IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
62.2%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property JIS G4805 SUJ2 EN ISO 4957 1.2316
Standard JIS G 4805:1999 EN ISO 4957:2018
Category Tool & Die Steels Tool & Die Steels
C (%) 0.95–1.10 ≤0.06
Si (%) 0.15–0.35 ≤0.50
Mn (%) ≤0.50 ≤1.00
Cr (%) 1.30–1.60 15.5–17.5
S (%) ≤0.025 Not specified
P (%) ≤0.025 Not specified
Mo (%) Not specified 0.80–1.30
Ni (%) Not specified 0.80–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4805 SUJ2 EN ISO 4957 1.2316
Tensile Strength ≥650 MPa (annealed) Not specified
Hardness HRC 60–64 (hardened) 28–34 (pre-hardened)
Hardness HB 183–229 (annealed) Not specified
Hardness HRC (hardened) Not specified 38–44
Corrosion Resistance Not specified Good in humid/corrosive environments
Typical Applications
JIS G4805 SUJ2
Ball bearings, roller bearings, bearing races, precision rolls
EN ISO 4957 1.2316
Plastic injection moulds for corrosive materials, food packaging moulds
Key Differences
Can JIS G4805 SUJ2 Be Substituted With EN ISO 4957 1.2316?
JIS G4805 SUJ2 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
JIS G4805 SUJ2
Round Bar → (6 listings)
Diameter: 60–80 mm (2.36–3.15 in)
Length: 5000–6900 mm (196.85–271.65 in)
EN ISO 4957 1.2316
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 2600–2700 mm (102.36–106.3 in)
On M-EX Right Now
JIS G4805 SUJ2
6 active listings and RFQs →
EN ISO 4957 1.2316
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4805 SUJ2 and EN ISO 4957 1.2316?
JIS G4805 SUJ2 specifies S, P which are not specified for EN ISO 4957 1.2316. EN ISO 4957 1.2316 specifies Mo, Ni which are not specified for JIS G4805 SUJ2.
Can JIS G4805 SUJ2 be substituted with EN ISO 4957 1.2316?
JIS G4805 SUJ2 and EN ISO 4957 1.2316 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.