Post Stock Login Register

NF A35-552 42CD4 vs IS 4367 10Cr9Mo10

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

NF A35-552 42CD4 (NF A35-552:1986) and IS 4367 10Cr9Mo10 (IS 4367:1991) are both steel grades. Both fall under the Alloy Steel category. NF A35-552 42CD4 is defined under Association Francaise de Normalisation (NF), originating from France, while IS 4367 10Cr9Mo10 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, NF A35-552 42CD4 vs IS 4367 10Cr9Mo10 is a 57.4% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With NF A35-552 42CD4:
GOST 4543 12HN3A GB/T 3077 12Cr2Ni4A NF A35-565 100C6 UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 7) 10Cr36Mo10H EN 10028-2 10CrMo9-10
Match Breakdown
CHEMISTRY MATCH
57.4%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property NF A35-552 42CD4 IS 4367 10Cr9Mo10
Standard NF A35-552:1986 IS 4367:1991
Category Alloy Steel Alloy Steel
C (%) 0.38–0.45 <=0.15
Si (%) 0.15–0.35 <=0.50
Mn (%) 0.60–0.90 0.40-0.70
Cr (%) 0.90–1.20 2.00-2.50
Mo (%) 0.15–0.30 0.90-1.10
Ni (%) Not specified <=0.30
S (%) Not specified <=0.035
P (%) Not specified <=0.035
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property NF A35-552 42CD4 IS 4367 10Cr9Mo10
Tensile Strength 900–1100 MPa 410-590 MPa
Yield Strength ≥700 MPa 245 MPa min
Elongation ≥12% >=18%
Hardness 263–313 HB Not specified
Izod Impact Not specified 55 J min
Hardness (soft annealed) Not specified <=187 HB
Condition Not specified Normalised and tempered, ruling section up to 50 mm
Typical Applications
NF A35-552 42CD4
Gears, shafts, crankshafts, high tensile fasteners
IS 4367 10Cr9Mo10
Not documented
Key Differences
Can NF A35-552 42CD4 Be Substituted With IS 4367 10Cr9Mo10?
NF A35-552 42CD4 and IS 4367 10Cr9Mo10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
NF A35-552 42CD4
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5900–6800 mm (232.28–267.72 in)
IS 4367 10Cr9Mo10
No active listings currently.
On M-EX Right Now
NF A35-552 42CD4
3 active listings and RFQs →
IS 4367 10Cr9Mo10
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between NF A35-552 42CD4 and IS 4367 10Cr9Mo10?
IS 4367 10Cr9Mo10 specifies Ni, S, P which are not specified for NF A35-552 42CD4.
Can NF A35-552 42CD4 be substituted with IS 4367 10Cr9Mo10?
NF A35-552 42CD4 and IS 4367 10Cr9Mo10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.