Post Stock Login Register

SAE J403 1053 vs BS 970 (Part 3) 070M55

Close Alternative — 84.7% match based on chemical composition and mechanical property overlap.

SAE J403 1053 (SAE J403:2001) and BS 970 (Part 3) 070M55 (BS 970 (Part 3):1991) are both steel grades. Both fall under the Carbon Steel category. SAE J403 1053 is typically used for chemistry-only grade; product scope as listed in the composition notes, while BS 970 (Part 3) 070M55 is commonly used for used for springs, blades, wear plates, hand tools, shafts, and cutting components.. SAE J403 1053 is defined under SAE International, originating from United States, while BS 970 (Part 3) 070M55 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, SAE J403 1053 vs BS 970 (Part 3) 070M55 is a 84.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 84.7%.

Frequently Compared With SAE J403 1053:
BS 970 (Part 1) 040A10 BS 970 (Part 1) 080A20 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 045A10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045M10
Match Breakdown
CHEMISTRY MATCH
84.7%
MECHANICAL MATCH
No shared data
OVERALL
84.7%
Specifications
Property SAE J403 1053 BS 970 (Part 3) 070M55
Standard SAE J403:2001 BS 970 (Part 3):1991
Category Carbon Steel Carbon Steel
C (%) 0.48-0.55 0.50-0.60
Mn (%) 0.70-1.00 0.50-0.90
P (%) <=0.030 <=0.05
S (%) <=0.050 <=0.05
Si (%) Not specified 0.10-0.40
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Typical Applications
SAE J403 1053
Chemistry-only grade; product scope as listed in the composition notes
BS 970 (Part 3) 070M55
Used for springs, blades, wear plates, hand tools, shafts, and cutting components.
Key Differences
Can SAE J403 1053 Be Substituted With BS 970 (Part 3) 070M55?
SAE J403 1053 and BS 970 (Part 3) 070M55 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
SAE J403 1053
No active listings currently.
BS 970 (Part 3) 070M55
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 4800–5800 mm (188.98–228.35 in)
On M-EX Right Now
SAE J403 1053
0 active listings and RFQs →
BS 970 (Part 3) 070M55
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between SAE J403 1053 and BS 970 (Part 3) 070M55?
BS 970 (Part 3) 070M55 specifies Si which is not specified for SAE J403 1053.
Can SAE J403 1053 be substituted with BS 970 (Part 3) 070M55?
SAE J403 1053 and BS 970 (Part 3) 070M55 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.