Post Stock Login Register

AISI 3310 vs BS 970 (Part 1) 655M13

Close Alternative — 80.6% match based on chemical composition and mechanical property overlap.

AISI 3310 and BS 970 (Part 1) 655M13 (BS 970 (Part 1):1983) are both steel grades. Both fall under the Alloy Steel category. AISI 3310 is typically used for aircraft gears, heavily stressed case hardened parts, while BS 970 (Part 1) 655M13 is commonly used for case hardening steel for mechanical and allied engineering purposes (table 11 mechanical properties).. AISI 3310 is defined under AISI, originating from United States, while BS 970 (Part 1) 655M13 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, AISI 3310 vs BS 970 (Part 1) 655M13 is a 80.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 80.6%.

Frequently Compared With AISI 3310:
UNI 11234 100Cr6 NF A35-565 100C6 GB/T 3077 12Cr2Ni4A GOST 4543 12HN3A IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
80.6%
MECHANICAL MATCH
No shared data
OVERALL
80.6%
Specifications
Property AISI 3310 BS 970 (Part 1) 655M13
Standard AISI BS 970 (Part 1):1983
Category Alloy Steel Alloy Steel
C (%) 0.08–0.13 0.10-0.16
Mn (%) 0.40-0.60 0.35-0.60
Cr (%) 1.40–1.75 0.70-1.00
Ni (%) 3.25–3.75 3.00-3.75
P (%) Not specified <=0.035
S (%) Not specified <=0.040
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property AISI 3310 BS 970 (Part 1) 655M13
Tensile Strength 900–1100 MPa Not specified
Case Hardness HRC 60–65 Not specified
Elongation ≥10% Not specified
Typical Applications
AISI 3310
Aircraft gears, heavily stressed case hardened parts
BS 970 (Part 1) 655M13
Case hardening steel for mechanical and allied engineering purposes (Table 11 mechanical properties).
Key Differences
Can AISI 3310 Be Substituted With BS 970 (Part 1) 655M13?
AISI 3310 and BS 970 (Part 1) 655M13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
AISI 3310
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 4900–5600 mm (192.91–220.47 in)
BS 970 (Part 1) 655M13
No active listings currently.
On M-EX Right Now
AISI 3310
3 active listings and RFQs →
BS 970 (Part 1) 655M13
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between AISI 3310 and BS 970 (Part 1) 655M13?
BS 970 (Part 1) 655M13 specifies P, S which are not specified for AISI 3310.
Can AISI 3310 be substituted with BS 970 (Part 1) 655M13?
AISI 3310 and BS 970 (Part 1) 655M13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.