Post Stock Login Register

ASTM A959 SS410 vs GOST 5632 12Kh13

Close Alternative — 79.4% match based on chemical composition and mechanical property overlap.

ASTM A959 SS410 (ASTM A959:2011) and GOST 5632 12Kh13 (GOST 5632-2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 SS410 is typically used for cutlery, turbine blades, surgical instruments, fasteners, while GOST 5632 12Kh13 is commonly used for turbine blades, pump shafts, fasteners, cutlery. ASTM A959 SS410 is defined under ASTM International (United States).

As per chemical composition, ASTM A959 SS410 vs GOST 5632 12Kh13 is a 79.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 79.4%.

Frequently Compared With ASTM A959 SS410:
EN 10088-1 1.4006 GB/T 3280 06Cr19Ni10 EN 10088-1 1.4401 GOST 5632 06Kh23N28 EN 10088-1 1.4301 EN 10088-1 1.4845 GOST 5632 08X18H10 ASTM A959 .- IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
79.4%
MECHANICAL MATCH
No shared data
OVERALL
79.4%
Specifications
Property ASTM A959 SS410 GOST 5632 12Kh13
Standard ASTM A959:2011 GOST 5632-2014
Category Stainless Steel Stainless Steel
C (%) <=0.15 0.09–0.15
Cr (%) 11.5-13.5 12.0–14.0
Mn (%) <=1.00 ≤0.80
P (%) <=0.040 Not specified
S (%) <=0.030 Not specified
Si (%) <=1.00 ≤0.80
Ni (%) Not specified ≤0.60
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 SS410 GOST 5632 12Kh13
Tensile Strength Not specified ≥540 MPa (annealed)
Hardness HRC Not specified 36–45 (hardened)
Typical Applications
ASTM A959 SS410
Cutlery, turbine blades, surgical instruments, fasteners
GOST 5632 12Kh13
Turbine blades, pump shafts, fasteners, cutlery
Key Differences
Can ASTM A959 SS410 Be Substituted With GOST 5632 12Kh13?
ASTM A959 SS410 and GOST 5632 12Kh13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
ASTM A959 SS410
Round Bar → (3 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 2800–3300 mm (110.24–129.92 in)
GOST 5632 12Kh13
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
ASTM A959 SS410
3 active listings and RFQs →
GOST 5632 12Kh13
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 SS410 and GOST 5632 12Kh13?
ASTM A959 SS410 specifies P, S which are not specified for GOST 5632 12Kh13. GOST 5632 12Kh13 specifies Ni which is not specified for ASTM A959 SS410.
Can ASTM A959 SS410 be substituted with GOST 5632 12Kh13?
ASTM A959 SS410 and GOST 5632 12Kh13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.