Post Stock Login Register

ASTM A105 vs EN 10025-2 E295

Related Material — 57.2% match based on chemical composition and mechanical property overlap.

ASTM A105 (ASTM A105) and EN 10025-2 E295 (EN 10025-2:2019) are both steel grades. ASTM A105 is classified under Carbon Steel, while EN 10025-2 E295 is classified under Structural Steel — a different category, which is worth noting alongside the chemistry match below. ASTM A105 is typically used for flanges, fittings, valves, pressure piping components, forged pressure vessel parts, while EN 10025-2 E295 is commonly used for hot rolled products of structural steels. ASTM A105 is defined under ASTM International, originating from United States, while EN 10025-2 E295 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A105 vs EN 10025-2 E295 is a 85.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a related material overall at 57.2%.

Frequently Compared With ASTM A105:
BS 970 (Part 3) 070M55 BS 970 (Part 1) 040A10 BS 970 (Part 1) 040A04 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32
Match Breakdown
CHEMISTRY MATCH
85.8%
MECHANICAL MATCH
0%
OVERALL
57.2%
Specifications
Property ASTM A105 EN 10025-2 E295
Standard ASTM A105 EN 10025-2:2019
Category Carbon Steel Structural Steel
C (%) ≤0.35 Not specified
Mn (%) 0.60–1.05 Not specified
Si (%) 0.10–0.35 Not specified
P (%) ≤0.035 <=0.045
S (%) ≤0.040 <=0.045
N (%) Not specified <=0.012
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A105 EN 10025-2 E295
Tensile Strength 485 MPa min 470-610 MPa
Yield Strength 250 MPa min >=295 MPa
Elongation ≥22% >=20%
Hardness ≤197 HB Not specified
Condition Not specified Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces
Typical Applications
ASTM A105
Flanges, fittings, valves, pressure piping components, forged pressure vessel parts
EN 10025-2 E295
Hot rolled products of structural steels
Key Differences
Can ASTM A105 Be Substituted With EN 10025-2 E295?
ASTM A105 and EN 10025-2 E295 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A105
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 6100–7000 mm (240.16–275.59 in)
EN 10025-2 E295
No active listings currently.
On M-EX Right Now
ASTM A105
2 active listings and RFQs →
EN 10025-2 E295
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A105 and EN 10025-2 E295?
Different category: ASTM A105 is Carbon Steel, EN 10025-2 E295 is Structural Steel. ASTM A105 specifies C, Mn, Si which are not specified for EN 10025-2 E295. EN 10025-2 E295 specifies N which is not specified for ASTM A105.
Can ASTM A105 be substituted with EN 10025-2 E295?
ASTM A105 and EN 10025-2 E295 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.