Post Stock Login Register

ASTM A240/A240M S44535 vs EN 10088-1 1.4401

Minimal Match — 33% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S44535 (ASTM A240/A240M:2025) and EN 10088-1 1.4401 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S44535 is typically used for pressure vessels and general applications (plate, sheet and strip), while EN 10088-1 1.4401 is commonly used for marine, chemical processing, pharmaceutical equipment. ASTM A240/A240M S44535 is defined under ASTM International, originating from United States, while EN 10088-1 1.4401 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A240/A240M S44535 vs EN 10088-1 1.4401 is a 49.4% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 33%.

Frequently Compared With ASTM A240/A240M S44535:
EN 10088-1 1.4845 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo GOST 5632 06Kh23N28 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10
Match Breakdown
CHEMISTRY MATCH
49.4%
MECHANICAL MATCH
0%
OVERALL
33%
Specifications
Property ASTM A240/A240M S44535 EN 10088-1 1.4401
Standard ASTM A240/A240M:2025 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 ≤0.07
Mn (%) 0.30-0.80 ≤2.00
P (%) <=0.050 Not specified
S (%) <=0.020 Not specified
Si (%) <=0.50 ≤1.00
Cr (%) 20.0-24.0 16.5–18.5
Cu (%) <=0.50 Not specified
La (%) 0.04-0.20 Not specified
Ti (%) 0.03-0.20 Not specified
Al (%) <=0.50 Not specified
Ni (%) Not specified 10.5–13.5
Mo (%) Not specified 2.0–2.5
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S44535 EN 10088-1 1.4401
Tensile Strength >=400 MPa ≥520 MPa
Yield Strength >=250 MPa ≥210 MPa
Elongation >=25% ≥40%
Hardness <=90 HRBW ≤215 HB
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Typical Applications
ASTM A240/A240M S44535
Pressure vessels and general applications (plate, sheet and strip)
EN 10088-1 1.4401
Marine, chemical processing, pharmaceutical equipment
Key Differences
Can ASTM A240/A240M S44535 Be Substituted With EN 10088-1 1.4401?
ASTM A240/A240M S44535 and EN 10088-1 1.4401 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A240/A240M S44535
No active listings currently.
EN 10088-1 1.4401
Sheet → (4 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3400 mm (98.43–133.86 in)
On M-EX Right Now
ASTM A240/A240M S44535
0 active listings and RFQs →
EN 10088-1 1.4401
4 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S44535 and EN 10088-1 1.4401?
ASTM A240/A240M S44535 specifies P, S, Cu, La which are not specified for EN 10088-1 1.4401. EN 10088-1 1.4401 specifies Ni, Mo which are not specified for ASTM A240/A240M S44535.
Can ASTM A240/A240M S44535 be substituted with EN 10088-1 1.4401?
ASTM A240/A240M S44535 and EN 10088-1 1.4401 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.