Post Stock Login Register

ASTM A240/A240M S46800 vs EN 10088-1 1.4301

Minimal Match — 39.6% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S46800 (ASTM A240/A240M:2025) and EN 10088-1 1.4301 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S46800 is typically used for pressure vessels and general applications (plate, sheet and strip), while EN 10088-1 1.4301 is commonly used for food equipment, chemical vessels, architectural, kitchenware. ASTM A240/A240M S46800 is defined under ASTM International, originating from United States, while EN 10088-1 1.4301 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A240/A240M S46800 vs EN 10088-1 1.4301 is a 59.4% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 39.6%.

Frequently Compared With ASTM A240/A240M S46800:
ASTM A959 .- GOST 5632 06Kh23N28 GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
59.4%
MECHANICAL MATCH
0%
OVERALL
39.6%
Specifications
Property ASTM A240/A240M S46800 EN 10088-1 1.4301
Standard ASTM A240/A240M:2025 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 ≤0.07
Mn (%) <=1.00 ≤2.00
P (%) <=0.040 ≤0.045
S (%) <=0.030 ≤0.030
Si (%) <=1.00 ≤1.00
Cr (%) 18.0-20.0 17.5–19.5
Ni (%) <=0.50 8.0–10.5
N (%) <=0.030 Not specified
Ti (%) 0.07-0.30 Not specified
Nb (%) 0.10-0.60 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S46800 EN 10088-1 1.4301
Tensile Strength >=415 MPa ≥520 MPa
Yield Strength >=205 MPa ≥210 MPa
Elongation >=22% ≥45%
Hardness <=90 HRBW ≤215 HB
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Typical Applications
ASTM A240/A240M S46800
Pressure vessels and general applications (plate, sheet and strip)
EN 10088-1 1.4301
Food equipment, chemical vessels, architectural, kitchenware
Key Differences
Can ASTM A240/A240M S46800 Be Substituted With EN 10088-1 1.4301?
ASTM A240/A240M S46800 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A240/A240M S46800
No active listings currently.
EN 10088-1 1.4301
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3300 mm (98.43–129.92 in)
On M-EX Right Now
ASTM A240/A240M S46800
0 active listings and RFQs →
EN 10088-1 1.4301
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S46800 and EN 10088-1 1.4301?
ASTM A240/A240M S46800 specifies N, Ti, Nb which are not specified for EN 10088-1 1.4301.
Can ASTM A240/A240M S46800 be substituted with EN 10088-1 1.4301?
ASTM A240/A240M S46800 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.