Post Stock Login Register

ASTM A276/A276M S32506 vs IS 6603 X02Cr25Ni7Mo4CuWN

Close Alternative — 76.7% match based on chemical composition and mechanical property overlap.

ASTM A276/A276M S32506 (ASTM A276/A276M:2017) and IS 6603 X02Cr25Ni7Mo4CuWN (IS 6603:2024) are both steel grades. Both fall under the Stainless Steel category. ASTM A276/A276M S32506 is typically used for stainless steel bars and shapes (hot-finished or cold-finished), while IS 6603 X02Cr25Ni7Mo4CuWN is commonly used for general purposes, semi-finished products, bars, wire rods and bright bars. ASTM A276/A276M S32506 is defined under ASTM International, originating from United States, while IS 6603 X02Cr25Ni7Mo4CuWN is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, ASTM A276/A276M S32506 vs IS 6603 X02Cr25Ni7Mo4CuWN is a 76.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.7%.

Frequently Compared With ASTM A276/A276M S32506:
GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H ASTM A959 .-
Match Breakdown
CHEMISTRY MATCH
76.7%
MECHANICAL MATCH
No shared data
OVERALL
76.7%
Specifications
Property ASTM A276/A276M S32506 IS 6603 X02Cr25Ni7Mo4CuWN
Standard ASTM A276/A276M:2017 IS 6603:2024
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Mn (%) <=1.00 <=1.00
P (%) <=0.040 <=0.035
S (%) <=0.015 <=0.015
Si (%) <=0.90 <=1.00
Cr (%) 24.0-26.0 24.0-26.0
Ni (%) 5.5-7.2 6.0-8.0
Mo (%) 3.0-3.5 3.0-4.0
N (%) 0.08-0.20 0.20-0.30
W (%) 0.05-0.30 0.50-1.00
Cu (%) Not specified 0.50-1.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A276/A276M S32506 IS 6603 X02Cr25Ni7Mo4CuWN
Tensile Strength Not specified >=730 MPa
Yield Strength Not specified >=530 MPa
Elongation Not specified >=25%
Hardness Not specified <=290 HB
Condition Not specified Solution annealed, conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Tensile Strength is a minimum as printed, hardness for guidance only
Typical Applications
ASTM A276/A276M S32506
Stainless steel bars and shapes (hot-finished or cold-finished)
IS 6603 X02Cr25Ni7Mo4CuWN
General purposes, semi-finished products, bars, wire rods and bright bars
Key Differences
Can ASTM A276/A276M S32506 Be Substituted With IS 6603 X02Cr25Ni7Mo4CuWN?
ASTM A276/A276M S32506 and IS 6603 X02Cr25Ni7Mo4CuWN are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A276/A276M S32506
0 active listings and RFQs →
IS 6603 X02Cr25Ni7Mo4CuWN
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A276/A276M S32506 and IS 6603 X02Cr25Ni7Mo4CuWN?
IS 6603 X02Cr25Ni7Mo4CuWN specifies Cu which is not specified for ASTM A276/A276M S32506.
Can ASTM A276/A276M S32506 be substituted with IS 6603 X02Cr25Ni7Mo4CuWN?
ASTM A276/A276M S32506 and IS 6603 X02Cr25Ni7Mo4CuWN are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.