Minimal Match — 34.9% match
based on chemical composition and mechanical property overlap.
BS 970 EN16 (BS 970:1955) and IS 11169 (Part 1) 10Ni5Cr4 (IS 11169 (Part 1):2022) are both steel grades.
Both fall under the Alloy Steel category.
BS 970 EN16 is typically used for high tensile bolts, studs, general engineering, while IS 11169 (Part 1) 10Ni5Cr4 is commonly used for cold heading and cold extrusion of parts that are case hardened; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, annex b).
BS 970 EN16 is defined under British Standards (BS), originating from United Kingdom, while IS 11169 (Part 1) 10Ni5Cr4 is defined under Bureau of Indian Standards (IS), originating from India.
As per chemical composition, BS 970 EN16 vs IS 11169 (Part 1) 10Ni5Cr4 is a 52.4% match.
As per mechanical properties, the match is 0%.
Combined, this makes them a minimal match overall at 34.9%.
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
BS 970 EN16
IS 11169 (Part 1) 10Ni5Cr4
Tensile Strength
≥695 MPa (45 tons/sq in, converted)
Not specified
Yield Strength
≥525 MPa (34 tons/sq in, converted)
Not specified
Elongation
≥22%
Not specified
Hardness
201-255 HB
Not specified
Condition
Hardened and tempered R, ruling section 6 in (lowest-strength condition of the standard)
Not specified
Hardness, ferrite-pearlite (+FP)
Not specified
137-187 HB
Tensile Strength, annealed (+AC)
Not specified
<=520 MPa (over 5 to 40 mm)
Typical Applications
BS 970 EN16
High tensile bolts, studs, general engineering
IS 11169 (Part 1) 10Ni5Cr4
Cold heading and cold extrusion of parts that are case hardened; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex B)
Key Differences
BS 970 EN16 specifies Mo which is not specified for IS 11169 (Part 1) 10Ni5Cr4.
IS 11169 (Part 1) 10Ni5Cr4 specifies Cr, Cu, Ni which are not specified for BS 970 EN16.
Can BS 970 EN16 Be Substituted With IS 11169 (Part 1) 10Ni5Cr4?
BS 970 EN16 and IS 11169 (Part 1) 10Ni5Cr4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
What is the difference between BS 970 EN16 and IS 11169 (Part 1) 10Ni5Cr4?
BS 970 EN16 specifies Mo which is not specified for IS 11169 (Part 1) 10Ni5Cr4. IS 11169 (Part 1) 10Ni5Cr4 specifies Cr, Cu, Ni which are not specified for BS 970 EN16.
Can BS 970 EN16 be substituted with IS 11169 (Part 1) 10Ni5Cr4?
BS 970 EN16 and IS 11169 (Part 1) 10Ni5Cr4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.