Post Stock Login Register

BS 970 EN41C vs BS 970 (Part 1) 709M40

Close Alternative — 72.9% match based on chemical composition and mechanical property overlap.

BS 970 EN41C (BS 970:1955) and BS 970 (Part 1) 709M40 (BS 970 (Part 1):1991) are both steel grades. Both fall under the Alloy Steel category. BS 970 EN41C is typically used for precision nitrided components, gauges, while BS 970 (Part 1) 709M40 is commonly used for used for aircraft parts, heavy-duty gears, transmission shafts, connecting rods, crankshafts, and engineering fasteners.. BS 970 EN41C is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 1) 709M40 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 EN41C vs BS 970 (Part 1) 709M40 is a 72.9% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 72.9%.

Frequently Compared With BS 970 EN41C:
NF A35-565 100C6 GOST 4543 12HN3A GB/T 3077 12Cr2Ni4A UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 07Cr4Mo6 IS 1570 (Part 4) 105Cr5 IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
72.9%
MECHANICAL MATCH
No shared data
OVERALL
72.9%
Specifications
Property BS 970 EN41C BS 970 (Part 1) 709M40
Standard BS 970:1955 BS 970 (Part 1):1991
Category Alloy Steel Alloy Steel
C (%) 0.38–0.48 0.36-0.44
Mn (%) 0.40–0.70 0.70-1.00
Cr (%) 1.40–1.80 0.90-1.20
Al (%) 0.85–1.20 Not specified
Mo (%) 0.20–0.30 0.25-0.35
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN41C BS 970 (Part 1) 709M40
Tensile Strength 900–1050 MPa Not specified
Surface Hardness HV ≥950 (nitrided) Not specified
Typical Applications
BS 970 EN41C
Precision nitrided components, gauges
BS 970 (Part 1) 709M40
Used for aircraft parts, heavy-duty gears, transmission shafts, connecting rods, crankshafts, and engineering fasteners.
Key Differences
Can BS 970 EN41C Be Substituted With BS 970 (Part 1) 709M40?
BS 970 EN41C and BS 970 (Part 1) 709M40 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
BS 970 EN41C
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5300–5700 mm (208.66–224.41 in)
BS 970 (Part 1) 709M40
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 6600–6800 mm (259.84–267.72 in)
On M-EX Right Now
BS 970 EN41C
3 active listings and RFQs →
BS 970 (Part 1) 709M40
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN41C and BS 970 (Part 1) 709M40?
BS 970 EN41C specifies Al which is not specified for BS 970 (Part 1) 709M40.
Can BS 970 EN41C be substituted with BS 970 (Part 1) 709M40?
BS 970 EN41C and BS 970 (Part 1) 709M40 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.