Post Stock Login Register

BS 970 EN58J vs BS 970 (Part 3) 316S33

Close Alternative — 74.2% match based on chemical composition and mechanical property overlap.

BS 970 EN58J (BS 970:1955) and BS 970 (Part 3) 316S33 (BS 970 (Part 3):1991) are both steel grades. Both fall under the Stainless Steel category. BS 970 EN58J is defined under British Standards (BS), originating from United Kingdom, while BS 970 (Part 3) 316S33 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 EN58J vs BS 970 (Part 3) 316S33 is a 74.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 74.2%.

Frequently Compared With BS 970 EN58J:
IS 1570 (Part 7) 12Cr12Ni2Mo EN 10088-1 1.4301 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
74.2%
MECHANICAL MATCH
No shared data
OVERALL
74.2%
Specifications
Property BS 970 EN58J BS 970 (Part 3) 316S33
Standard BS 970:1955 BS 970 (Part 3):1991
Category Stainless Steel Stainless Steel
C (%) <=0.12 <=0.07
Si (%) >=0.20 <=1.0
Mn (%) <=2.00 <=2.0
Ni (%) 8.0-12.0 11.0-14.0
Cr (%) 17.0-20.0 16.5-18.5
Mo (%) 2.50-3.50 2.50-3.00
S (%) <=0.045 <=0.030
P (%) <=0.045 <=0.045
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 EN58J BS 970 (Part 3) 316S33
Tensile Strength ≥541 MPa (35 tons/sq in, converted) Not specified
Yield Strength ≥185 MPa (12 tons/sq in, converted) Not specified
Elongation ≥30% Not specified
Condition , ruling section 6 in (lowest-strength condition of the standard) Not specified
Typical Applications
BS 970 EN58J
Not documented
BS 970 (Part 3) 316S33
Bright cold finished bars (cold drawn, turned or precision ground) for general engineering purposes, in straight lengths; austenitic stainless and heat resisting steel (Table 18)
Can BS 970 EN58J Be Substituted With BS 970 (Part 3) 316S33?
BS 970 EN58J and BS 970 (Part 3) 316S33 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
BS 970 EN58J
0 active listings and RFQs →
BS 970 (Part 3) 316S33
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 EN58J and BS 970 (Part 3) 316S33?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can BS 970 EN58J be substituted with BS 970 (Part 3) 316S33?
BS 970 EN58J and BS 970 (Part 3) 316S33 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.