Post Stock Login Register

BS 970 (Part 3) 080M30 vs BS 970 EN5D

Strong Match — 95.7% match based on chemical composition and mechanical property overlap.

BS 970 (Part 3) 080M30 (BS 970 (Part 3):1991) and BS 970 EN5D (BS 970:1955) are both steel grades. Both fall under the Carbon Steel category. BS 970 (Part 3) 080M30 is typically used for used for shafts, gears, axles, couplings, bolts, and general engineering components., while BS 970 EN5D is commonly used for bars for machining. BS 970 (Part 3) 080M30 is defined under British Standards (BS), originating from United Kingdom, while BS 970 EN5D is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, BS 970 (Part 3) 080M30 vs BS 970 EN5D is a 95.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 95.7%.

Frequently Compared With BS 970 (Part 3) 080M30:
BS 970 (Part 1) 040A10 BS 970 (Part 3) 070M55 BS 970 (Part 1) 045A10 BS 970 (Part 1) 040A12 BS 970 (Part 1) 040A04 BS 970 (Part 3) 045A10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 060A32
Match Breakdown
CHEMISTRY MATCH
95.7%
MECHANICAL MATCH
No shared data
OVERALL
95.7%
Specifications
Property BS 970 (Part 3) 080M30 BS 970 EN5D
Standard BS 970 (Part 3):1991 BS 970:1955
Category Carbon Steel Carbon Steel
C (%) 0.26-0.34 0.25-0.35
Si (%) 0.10-0.40 0.05-0.35
Mn (%) 0.60-1.00 0.60-1.00
P (%) <=0.05 <=0.060
S (%) <=0.05 <=0.060
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property BS 970 (Part 3) 080M30 BS 970 EN5D
Tensile Strength Not specified ≥541 MPa (35 tons/sq in, converted)
Elongation Not specified ≥15%
Hardness Not specified ≤229 HB
Condition Not specified size (diameter or width across flats) Over 3/4 to 1 1/2 in (lowest-strength condition of the standard)
Typical Applications
BS 970 (Part 3) 080M30
Used for shafts, gears, axles, couplings, bolts, and general engineering components.
BS 970 EN5D
Bars for machining
Can BS 970 (Part 3) 080M30 Be Substituted With BS 970 EN5D?
BS 970 (Part 3) 080M30 and BS 970 EN5D overlap closely enough on chemistry and mechanical properties that BS 970 EN5D is often considered as a substitute for BS 970 (Part 3) 080M30 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
BS 970 (Part 3) 080M30
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5300–6500 mm (208.66–255.91 in)
BS 970 EN5D
No active listings currently.
On M-EX Right Now
BS 970 (Part 3) 080M30
2 active listings and RFQs →
BS 970 EN5D
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between BS 970 (Part 3) 080M30 and BS 970 EN5D?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can BS 970 (Part 3) 080M30 be substituted with BS 970 EN5D?
BS 970 (Part 3) 080M30 and BS 970 EN5D overlap closely enough on chemistry and mechanical properties that BS 970 EN5D is often considered as a substitute for BS 970 (Part 3) 080M30 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.