Post Stock Login Register

DIN 17200 30CrMoV9 vs DIN 17211 41CrAlMo7-4

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

DIN 17200 30CrMoV9 (DIN 17200:1986) and DIN 17211 41CrAlMo7-4 (DIN 17211:1987) are both steel grades. Both fall under the Alloy Steel category. DIN 17200 30CrMoV9 is typically used for power generation components, rotors, turbine parts, while DIN 17211 41CrAlMo7-4 is commonly used for used for nitrided shafts, gears, crankshafts, spindles, extrusion screws, and wear-resistant machine components.. DIN 17200 30CrMoV9 is defined under Deutsches Institut fur Normung (DIN), originating from Germany, while DIN 17211 41CrAlMo7-4 is defined under Deutsches Institut fur Normung (DIN), originating from Germany.

As per chemical composition, DIN 17200 30CrMoV9 vs DIN 17211 41CrAlMo7-4 is a 65.7% match. As per mechanical properties, the match is 100%. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With DIN 17200 30CrMoV9:
UNI 11234 100Cr6 GB/T 3077 12Cr2Ni4A NF A35-565 100C6 GOST 4543 12HN3A IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 07Cr4Mo6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 07Cr4Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
65.7%
MECHANICAL MATCH
100%
OVERALL
69.9%
Specifications
Property DIN 17200 30CrMoV9 DIN 17211 41CrAlMo7-4
Standard DIN 17200:1986 DIN 17211:1987
Category Alloy Steel Alloy Steel
C (%) 0.26–0.34 0.38–0.48
Mn (%) 0.40–0.70 0.40–0.70
Cr (%) 2.30–2.70 1.40–1.80
Mo (%) 0.90–1.10 0.20–0.30
V (%) 0.18–0.28 Not specified
Al (%) Not specified 0.85–1.20
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN 17200 30CrMoV9 DIN 17211 41CrAlMo7-4
Tensile Strength 900–1100 MPa 900–1050 MPa
Yield Strength ≥750 MPa Not specified
Elongation ≥13% Not specified
Surface Hardness HV Not specified ≥950 (nitrided)
Typical Applications
DIN 17200 30CrMoV9
Power generation components, rotors, turbine parts
DIN 17211 41CrAlMo7-4
Used for nitrided shafts, gears, crankshafts, spindles, extrusion screws, and wear-resistant machine components.
Key Differences
Can DIN 17200 30CrMoV9 Be Substituted With DIN 17211 41CrAlMo7-4?
DIN 17200 30CrMoV9 and DIN 17211 41CrAlMo7-4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
DIN 17200 30CrMoV9
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5500–6600 mm (216.54–259.84 in)
DIN 17211 41CrAlMo7-4
Round Bar → (4 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 4800–6900 mm (188.98–271.65 in)
On M-EX Right Now
DIN 17200 30CrMoV9
2 active listings and RFQs →
DIN 17211 41CrAlMo7-4
4 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN 17200 30CrMoV9 and DIN 17211 41CrAlMo7-4?
DIN 17200 30CrMoV9 specifies V which is not specified for DIN 17211 41CrAlMo7-4. DIN 17211 41CrAlMo7-4 specifies Al which is not specified for DIN 17200 30CrMoV9.
Can DIN 17200 30CrMoV9 be substituted with DIN 17211 41CrAlMo7-4?
DIN 17200 30CrMoV9 and DIN 17211 41CrAlMo7-4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.