Post Stock Login Register

DIN EN ISO 4957 1.2344 vs EN ISO 683-17 100Cr6

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

DIN EN ISO 4957 1.2344 (DIN EN ISO 4957:2018-11) and EN ISO 683-17 100Cr6 (EN ISO 683-17:2014) are both steel grades. Both fall under the Tool & Die Steels category. DIN EN ISO 4957 1.2344 is typically used for die casting dies, extrusion dies, forging dies, hot shear blades, mandrels, pressure die casting tooling, while EN ISO 683-17 100Cr6 is commonly used for rolling element bearings, precision components, cold work tooling. DIN EN ISO 4957 1.2344 is defined under European Standard (EN), originating from Europe, while EN ISO 683-17 100Cr6 is defined under European Standard (EN), originating from Europe.

As per chemical composition, DIN EN ISO 4957 1.2344 vs EN ISO 683-17 100Cr6 is a 62.7% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With DIN EN ISO 4957 1.2344:
GB/T 1299 4Cr5MoSiV GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS AISI 52100 IS 1570 (Part 6) 133T3 IS 1570 (Part 6) 55T8 IS 1570 (Part 6) 50T8 IS 1570 (Part 6) 75T6 IS 1570 (Part 6) 70T6 IS 1570 (Part 6) 60T6 IS 1570 (Part 6) 65T6 GB/T 1299 3Cr2W8V
Match Breakdown
CHEMISTRY MATCH
62.7%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6
Standard DIN EN ISO 4957:2018-11 EN ISO 683-17:2014
Category Tool & Die Steels Tool & Die Steels
C (%) 0.37–0.43 0.93–1.05
Mn (%) 0.30–0.50 0.25–0.45
Si (%) 0.90–1.20 0.15–0.35
Cr (%) 4.80–5.50 1.35–1.65
Mo (%) 1.20–1.50 Not specified
V (%) 0.90–1.10 Not specified
S (%) ≤0.030 ≤0.025
P (%) ≤0.030 ≤0.025
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6
Hardness (annealed) ≤229 HB Not specified
Hardness (hardened) 44–52 HRC Not specified
Tensile Strength 1200–1600 MPa ≥620 MPa (annealed)
Elongation ≥8% Not specified
Hardness HRC Not specified 60–66 (hardened)
Hardness HB Not specified 179–217 (annealed)
Typical Applications
DIN EN ISO 4957 1.2344
Die casting dies, extrusion dies, forging dies, hot shear blades, mandrels, pressure die casting tooling
EN ISO 683-17 100Cr6
Rolling element bearings, precision components, cold work tooling
Key Differences
Can DIN EN ISO 4957 1.2344 Be Substituted With EN ISO 683-17 100Cr6?
DIN EN ISO 4957 1.2344 and EN ISO 683-17 100Cr6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
DIN EN ISO 4957 1.2344
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–3700 mm (118.11–145.67 in)
EN ISO 683-17 100Cr6
Round Bar → (18 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–6500 mm (118.11–255.91 in)
On M-EX Right Now
DIN EN ISO 4957 1.2344
2 active listings and RFQs →
EN ISO 683-17 100Cr6
18 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN EN ISO 4957 1.2344 and EN ISO 683-17 100Cr6?
DIN EN ISO 4957 1.2344 specifies Mo, V which are not specified for EN ISO 683-17 100Cr6.
Can DIN EN ISO 4957 1.2344 be substituted with EN ISO 683-17 100Cr6?
DIN EN ISO 4957 1.2344 and EN ISO 683-17 100Cr6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.