Post Stock Login Register

DIN EN ISO 4957 1.2344 vs IS 1570 (Part 6) 50T8

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

DIN EN ISO 4957 1.2344 (DIN EN ISO 4957:2018-11) and IS 1570 (Part 6) 50T8 (IS 1570 (Part 6):1996) are both steel grades. Both fall under the Tool & Die Steels category. DIN EN ISO 4957 1.2344 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 6) 50T8 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, DIN EN ISO 4957 1.2344 vs IS 1570 (Part 6) 50T8 is a 49.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With DIN EN ISO 4957 1.2344:
GB/T 1299 4Cr5MoSiV EN ISO 683-17 100Cr6 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS AISI 52100 IS 1570 (Part 6) 133T3 IS 1570 (Part 6) 55T8 IS 1570 (Part 6) 75T6 IS 1570 (Part 6) 70T6 IS 1570 (Part 6) 60T6 IS 1570 (Part 6) 65T6 GB/T 1299 3Cr2W8V
Match Breakdown
CHEMISTRY MATCH
49.2%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property DIN EN ISO 4957 1.2344 IS 1570 (Part 6) 50T8
Standard DIN EN ISO 4957:2018-11 IS 1570 (Part 6):1996
Category Tool & Die Steels Tool & Die Steels
C (%) 0.37–0.43 0.45-0.55
Mn (%) 0.30–0.50 0.60-0.90
Si (%) 0.90–1.20 0.10-0.35
Cr (%) 4.80–5.50 <=0.20
Mo (%) 1.20–1.50 Not specified
V (%) 0.90–1.10 Not specified
S (%) ≤0.030 <=0.035
P (%) ≤0.030 <=0.035
Cu (%) Not specified <=0.25
Ni (%) Not specified <=0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN EN ISO 4957 1.2344 IS 1570 (Part 6) 50T8
Hardness (annealed) ≤229 HB Not specified
Hardness (hardened) 44–52 HRC Not specified
Tensile Strength 1200–1600 MPa Not specified
Elongation ≥8% Not specified
Typical Applications
DIN EN ISO 4957 1.2344
Die casting dies, extrusion dies, forging dies, hot shear blades, mandrels, pressure die casting tooling
IS 1570 (Part 6) 50T8
Not documented
Key Differences
Can DIN EN ISO 4957 1.2344 Be Substituted With IS 1570 (Part 6) 50T8?
DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) 50T8 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
DIN EN ISO 4957 1.2344
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–3700 mm (118.11–145.67 in)
IS 1570 (Part 6) 50T8
No active listings currently.
On M-EX Right Now
DIN EN ISO 4957 1.2344
2 active listings and RFQs →
IS 1570 (Part 6) 50T8
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) 50T8?
DIN EN ISO 4957 1.2344 specifies Mo, V which are not specified for IS 1570 (Part 6) 50T8. IS 1570 (Part 6) 50T8 specifies Cu, Ni which are not specified for DIN EN ISO 4957 1.2344.
Can DIN EN ISO 4957 1.2344 be substituted with IS 1570 (Part 6) 50T8?
DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) 50T8 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.