Post Stock Login Register

EN 10025-2 S275J2 vs AS/NZS Grade 500

Strong Match — 90.5% match based on chemical composition and mechanical property overlap.

EN 10025-2 S275J2 (EN 10025-2:2019) and AS/NZS Grade 500 (AS/NZS 3597:2008) are both steel grades. Both fall under the Structural Steel category. EN 10025-2 S275J2 is typically used for hot rolled products of structural steels, while AS/NZS Grade 500 is commonly used for heavy mining equipment, bulldozer blades, wear-resistant structural applications, large crane booms, offshore jackets.. EN 10025-2 S275J2 is defined under European Standard (EN), originating from Europe, while AS/NZS Grade 500 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, EN 10025-2 S275J2 vs AS/NZS Grade 500 is a 90.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 90.5%.

Other Structural Steel Grades to Compare With EN 10025-2 S275J2:
GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W CSA G40.21 400A CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
90.5%
MECHANICAL MATCH
No shared data
OVERALL
90.5%
Specifications
Property EN 10025-2 S275J2 AS/NZS Grade 500
Standard EN 10025-2:2019 AS/NZS 3597:2008
Category Structural Steel Structural Steel
C (%) <=0.21 max 0.2
Mn (%) <=1.50 max 1.6
P (%) <=0.025 max 0.03
S (%) <=0.025 max 0.03
Cu (%) <=0.55 Not specified
Si (%) Not specified max 0.55
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 S275J2 AS/NZS Grade 500
Tensile Strength 410-560 MPa Not specified
Yield Strength >=275 MPa Not specified
Elongation >=23% Not specified
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 S275J2
Hot rolled products of structural steels
AS/NZS Grade 500
Heavy mining equipment, bulldozer blades, wear-resistant structural applications, large crane booms, offshore jackets.
Key Differences
Can EN 10025-2 S275J2 Be Substituted With AS/NZS Grade 500?
EN 10025-2 S275J2 and AS/NZS Grade 500 overlap closely enough on chemistry and mechanical properties that AS/NZS Grade 500 is often considered as a substitute for EN 10025-2 S275J2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
EN 10025-2 S275J2
No active listings currently.
AS/NZS Grade 500
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3100–3600 mm (122.05–141.73 in)
On M-EX Right Now
EN 10025-2 S275J2
0 active listings and RFQs →
AS/NZS Grade 500
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 S275J2 and AS/NZS Grade 500?
EN 10025-2 S275J2 specifies Cu which is not specified for AS/NZS Grade 500. AS/NZS Grade 500 specifies Si which is not specified for EN 10025-2 S275J2.
Can EN 10025-2 S275J2 be substituted with AS/NZS Grade 500?
EN 10025-2 S275J2 and AS/NZS Grade 500 overlap closely enough on chemistry and mechanical properties that AS/NZS Grade 500 is often considered as a substitute for EN 10025-2 S275J2 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.