Post Stock Login Register

EN 10025-2:2019 S235J2 Steel: Specifications & Listings

EN 10025-2:2019 S235J2: S235J2: non-alloy structural steel, hot rolled flat and long products, impact tested at -20 deg C (steel number 1.0117). Specified in EN 10025-2:2019.

Forms: Plate Category: Structural Steel
Grade Details
GradeEN 10025-2:2019 S235J2
Standard EN 10025-2:2019
ApplicationsUsed for bridges, structural sections, storage tanks, industrial buildings, transport frames, and support structures.
Most Active InWest (Maharashtra, Gujarat)
Equivalent / Similar Grades
Grade Standard Region Live on M-EX
EN 10025-2 S235J0 EN 10025-2:2019 Europe 2 listings, 0 RFQs →
AS/NZS 1594 HA250 AS/NZS 1594:2025 Australia 2 listings, 0 RFQs →
CSA G40.21 260W CSA G40.21-13 (R2023) Canada 2 listings, 0 RFQs →
AS/NZS 3678 Grade 400 AS/NZS 3678:2016 Australia 2 listings, 0 RFQs →
AS/NZS 3678 Grade 450 AS/NZS 3678:2016 Australia 2 listings, 0 RFQs →
AS/NZS 1594 HA350 AS/NZS 1594:2025 Australia 2 listings, 0 RFQs →
AS/NZS Grade 500 AS/NZS 3597:2008 Australia 2 listings, 0 RFQs →
AS/NZS 3678 Grade 350L0 AS/NZS 3678:2016 Australia 0 listings, 2 RFQs →
Supply & Demand by FormSee Full Supply & Demand →
Plate →
Low Activity
Grade ComparisonCompare With a Specific Grade →
Grade Standard Match
EN 10025-2 S235J0 EN 10025-2:2019 Strong Match
EN 10025-2 S235JR EN 10025-2:2019 Strong Match
GB/T 700 Q235D GB/T 700:2006 Strong Match
GB/T 700 Q235C GB/T 700:2006 Strong Match
GB/T 700 Q235B GB/T 700:2006 Strong Match
GB/T 700 Q235A GB/T 700:2006 Strong Match
AS/NZS 3678 Grade 450 AS/NZS 3678:2016 Strong Match
AS/NZS Grade 500 AS/NZS 3597:2008 Strong Match
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Chemical Composition (%)
C Mn P S Cu
<=0.17 <=1.40 <=0.025 <=0.025 <=0.55
Mechanical Properties
Tensile Strength 360-510 MPa
Yield Strength >=235 MPa
Elongation >=26%
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces

More data from EN 10025-2:2019

From the standard
Yield strength by thickness 9 thickness ranges
Thickness (mm)Yield strength ReH, min (MPa)
up to 16235
over 16 to 40225
over 40 to 63215
over 63 to 80215
over 80 to 100215
over 100 to 150195
over 150 to 200185
over 200 to 250175
over 250 to 400165
For plate, strip and wide flats of width 600 mm or more the transverse direction applies.
Source: EN 10025-2:2019, Table 6
Tensile strength by thickness 5 thickness ranges
Thickness (mm)Tensile strength Rm (MPa)
under 3360 to 510
3 to 100360 to 510
over 100 to 150350 to 500
over 150 to 250340 to 490
over 250 to 400330 to 480
Source: EN 10025-2:2019, Table 6
Elongation by thickness 6 thickness ranges
Thickness (mm)Elongation A, longitudinal, min (%)Elongation A, transverse, min (%)
3 to 402624
over 40 to 632523
over 63 to 1002422
over 100 to 1502222
over 150 to 2502121
over 250 to 4002121
Gauge length 5.65 times square root of cross-section area; values for thin products under 3 mm (gauge length 80 mm) not shown.
Source: EN 10025-2:2019, Table 6 (concluded)
Impact energy KV2, longitudinal 3 thickness ranges
Thickness (mm)Test temperature (deg C)KV2 min (J)
up to 150-2027
over 150 to 250-2027
over 250 to 400-2027
Longitudinal test pieces; subsized specimens reduced in proportion to area.
Source: EN 10025-2:2019, Table 8
Maximum carbon equivalent value (CEV) 5 thickness ranges
Thickness (mm)CEV, max (%)
up to 300.35
over 30 to 400.35
over 40 to 1500.38
over 150 to 2500.40
over 250 to 4000.40
Based on heat analysis.
Source: EN 10025-2:2019, Table 5

Popular forms for this grade:

Plate (2)

Active EN 10025-2:2019 S235J2 Listings on M-EX (For Sale)

+ Create a Listing for this grade
EN 10025-2:2019 S235J2 Plate
8.400 MT
View Listing
EN 10025-2:2019 S235J2 Plate
3.000 MT
View Listing

Buyer RFQs for EN 10025-2:2019 S235J2

+ Post an RFQ for this grade

No open buyer requirements for EN 10025-2:2019 S235J2 at this time.

Register for Alerts