Post Stock Login Register

EN 10025-3 S420JR vs EN 10025-3 S460JR

Close Alternative — 81.9% match based on chemical composition and mechanical property overlap.

EN 10025-3 S420JR (EN 10025-3:2019) and EN 10025-3 S460JR (EN 10025-3:2019) are both steel grades. Both fall under the Structural Steel category. EN 10025-3 S420JR is typically used for used in bridges, heavy machinery frames, structural beams, offshore structures, and crane components., while EN 10025-3 S460JR is commonly used for used in bridges, welded steel structures, industrial buildings, heavy trailers, and crane booms.. EN 10025-3 S420JR is defined under European Standard (EN), originating from Europe, while EN 10025-3 S460JR is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10025-3 S420JR vs EN 10025-3 S460JR is a 93.2% match. As per mechanical properties, the match is 59.2%. Combined, this makes them a close alternative overall at 81.9%.

Frequently Compared With EN 10025-3 S420JR:
CSA G40.21 400A CSA G40.21 480W CSA G40.21 400W GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W ASTM A1008 SS Grade 50 ASTM A572 Gr.65 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
93.2%
MECHANICAL MATCH
59.2%
OVERALL
81.9%
Specifications
Property EN 10025-3 S420JR EN 10025-3 S460JR
Standard EN 10025-3:2019 EN 10025-3:2019
Category Structural Steel Structural Steel
C (%) 0.20 max 0.20 max
Si (%) 0.55 max 0.60 max
Mn (%) 1.70 max 1.70 max
P (%) 0.030 max 0.030 max
S (%) 0.030 max 0.030 max
N (%) 0.015 max Not specified
Nb (%) Not specified 0.06 max
V (%) Not specified 0.12 max
Ti (%) Not specified 0.05 max
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-3 S420JR EN 10025-3 S460JR
Tensile Strength 520-680 MPa 540-720 MPa
Yield Strength 420 MPa min 460 MPa min
Elongation 17% min 17% min
Hardness 170-220 HB 180-230 HB
Typical Applications
EN 10025-3 S420JR
Used in bridges, heavy machinery frames, structural beams, offshore structures, and crane components.
EN 10025-3 S460JR
Used in bridges, welded steel structures, industrial buildings, heavy trailers, and crane booms.
Key Differences
Can EN 10025-3 S420JR Be Substituted With EN 10025-3 S460JR?
EN 10025-3 S420JR and EN 10025-3 S460JR are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10025-3 S420JR
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3500–3900 mm (137.8–153.54 in)
EN 10025-3 S460JR
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–2500 mm (98.43–98.43 in)
On M-EX Right Now
EN 10025-3 S420JR
2 active listings and RFQs →
EN 10025-3 S460JR
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-3 S420JR and EN 10025-3 S460JR?
EN 10025-3 S420JR specifies N which is not specified for EN 10025-3 S460JR. EN 10025-3 S460JR specifies Nb, V, Ti which are not specified for EN 10025-3 S420JR.
Can EN 10025-3 S420JR be substituted with EN 10025-3 S460JR?
EN 10025-3 S420JR and EN 10025-3 S460JR are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.