Post Stock Login Register

EN 10025-5 S235J0W vs IS 11169 (Part 1) 38Cr4BT

Related Material — 63.4% match based on chemical composition and mechanical property overlap.

EN 10025-5 S235J0W (EN 10025-5:2019) and IS 11169 (Part 1) 38Cr4BT (IS 11169 (Part 1):2022) are both steel grades. EN 10025-5 S235J0W is classified under Structural Steel (Corten / Weathering), while IS 11169 (Part 1) 38Cr4BT is classified under Alloy Steel — a different category, which is worth noting alongside the chemistry match below. EN 10025-5 S235J0W is defined under European Standard (EN), originating from Europe, while IS 11169 (Part 1) 38Cr4BT is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10025-5 S235J0W vs IS 11169 (Part 1) 38Cr4BT is a 63.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 63.4%.

Frequently Compared With EN 10025-5 S235J0W:
EN 10025-5 S235J2W EN 10025-5 S355K2W EN 10025-5 S420K2W EN 10025-5 S460J2W
Other Structural Steel (Corten / Weathering) Grades to Compare With EN 10025-5 S235J0W:
CSA G40.21 260WT CSA G40.21 350A CSA G40.21 480A CSA G40.21 50W ASTM A588 ASTM A588 Grade A ASTM A588 Grade B ASTM A709 Grade HPS 70W
Match Breakdown
CHEMISTRY MATCH
63.4%
MECHANICAL MATCH
No shared data
OVERALL
63.4%
Specifications
Property EN 10025-5 S235J0W IS 11169 (Part 1) 38Cr4BT
Standard EN 10025-5:2019 IS 11169 (Part 1):2022
Category Structural Steel (Corten / Weathering) Alloy Steel
C (%) <=0.13 0.35-0.40
Si (%) <=0.40 0.15-0.30
Mn (%) 0.20-0.60 0.30-0.50
P (%) <=0.035 <=0.035
S (%) <=0.035 <=0.035
N (%) <=0.012 Not specified
Cr (%) 0.40-0.80 0.95-1.15
Cu (%) 0.25-0.55 <=0.15
B (%) Not specified 0.0005-0.003
Mo (%) Not specified <=0.05
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-5 S235J0W IS 11169 (Part 1) 38Cr4BT
Tensile Strength 360-510 MPa Not specified
Yield Strength >=235 MPa Not specified
Elongation >=26% Not specified
Condition Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks Not specified
Hardness, annealed (+AC) Not specified <=200 HBW
Typical Applications
EN 10025-5 S235J0W
Not documented
IS 11169 (Part 1) 38Cr4BT
Cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex C)
Key Differences
Can EN 10025-5 S235J0W Be Substituted With IS 11169 (Part 1) 38Cr4BT?
EN 10025-5 S235J0W and IS 11169 (Part 1) 38Cr4BT share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10025-5 S235J0W
0 active listings and RFQs →
IS 11169 (Part 1) 38Cr4BT
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-5 S235J0W and IS 11169 (Part 1) 38Cr4BT?
Different category: EN 10025-5 S235J0W is Structural Steel (Corten / Weathering), IS 11169 (Part 1) 38Cr4BT is Alloy Steel. EN 10025-5 S235J0W specifies N which is not specified for IS 11169 (Part 1) 38Cr4BT. IS 11169 (Part 1) 38Cr4BT specifies B, Mo which are not specified for EN 10025-5 S235J0W.
Can EN 10025-5 S235J0W be substituted with IS 11169 (Part 1) 38Cr4BT?
EN 10025-5 S235J0W and IS 11169 (Part 1) 38Cr4BT share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.