Post Stock Login Register

EN 10025-5 S460J2W vs CSA G40.21 350A

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10025-5 S460J2W (EN 10025-5:2019) and CSA G40.21 350A (CSA G40.21-13 (R2023)) are both steel grades. Both fall under the Structural Steel (Corten / Weathering) category. EN 10025-5 S460J2W is defined under European Standard (EN), originating from Europe, while CSA G40.21 350A is defined under Canadian Standards Association (CSA), originating from Canada.

As per chemical composition, EN 10025-5 S460J2W vs CSA G40.21 350A is a 82.2% match. As per mechanical properties, the match is 26.1%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10025-5 S460J2W:
EN 10025-5 S420K2W CSA G40.21 480A ASTM A588 EN 10025-5 S235J0W EN 10025-5 S420J5W EN 10025-5 S460J0W EN 10025-5 S460J4W EN 10025-5 S460J5W CSA G40.21 260WT CSA G40.21 50W ASTM A588 Grade B ASTM A709 Grade HPS 70W
Match Breakdown
CHEMISTRY MATCH
82.2%
MECHANICAL MATCH
26.1%
OVERALL
35%
Specifications
Property EN 10025-5 S460J2W CSA G40.21 350A
Standard EN 10025-5:2019 CSA G40.21-13 (R2023)
Category Structural Steel (Corten / Weathering) Structural Steel (Corten / Weathering)
C (%) <=0.20 max 0.19
Si (%) <=0.65 max 0.65
Mn (%) <=1.40 max 1.35
P (%) <=0.030 max 0.035
S (%) <=0.030 max 0.035
N (%) <=0.025 Not specified
Cr (%) 0.40-0.80 0.4-0.65
Cu (%) 0.25-0.55 0.25-0.4
Ni (%) Not specified 0.4-0.7
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-5 S460J2W CSA G40.21 350A
Tensile Strength 530-710 MPa 480-650 MPa
Yield Strength >=460 MPa 350 MPa min
Elongation >=17% Not specified
Condition Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks Not specified
Typical Applications
EN 10025-5 S460J2W
Not documented
CSA G40.21 350A
Exposed structural steelwork, bridges, retaining walls, coastal infrastructure, architectural facades.
Key Differences
Can EN 10025-5 S460J2W Be Substituted With CSA G40.21 350A?
EN 10025-5 S460J2W and CSA G40.21 350A share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10025-5 S460J2W
No active listings currently.
CSA G40.21 350A
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3300–3400 mm (129.92–133.86 in)
On M-EX Right Now
EN 10025-5 S460J2W
0 active listings and RFQs →
CSA G40.21 350A
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-5 S460J2W and CSA G40.21 350A?
EN 10025-5 S460J2W specifies N which is not specified for CSA G40.21 350A. CSA G40.21 350A specifies Ni which is not specified for EN 10025-5 S460J2W.
Can EN 10025-5 S460J2W be substituted with CSA G40.21 350A?
EN 10025-5 S460J2W and CSA G40.21 350A share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.